AMX NXD-430-WH Specifications Page 74
- Page / 146
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Setup Pages and Descriptions
62
NXD-430/435/435P 4.3” Wall/Flush Mount Touch Panels
System Settings - Master Tab
The Master tab of the System Settings page contains the necessary information for connecting to the network
Master.
FIG. 61 System Settings page - Master Tab
System Settings Page - Master Tab
Connection Status
icon:
Shows the current state of the panel’s connection to the Master (green = online, red =
offline). See the Connection Status Icon section on page 48 for details.
Type: This display-only field indicates whether the NetLinx Master communicates with the
panel via either USB or Ethernet. This is based on the cable connection from the rear.
Note: ICSNet is not a supported option on this panel.
• Ethernet is a CAT-5 cable (10/100Base T terminated in an RJ-45 connector) used
to network computers together and is used in most LAN (local area networks). This
description is also used to refer to both wired and wireless communication.
• USB option cannot be used on Modero panels that are not equipped with a USB
port.
Mode: Cycles between the different connection modes (URL, Listen, and Auto)
(ETHERNET Only - disabled when USB is selected)
• URL - In this mode, enter the IP/URL, Master Port Number, and username/
password (if used) on the Master.
The System Number field is read-only because the panel obtains this information
from the communicating Master.
• Listen - In this mode, add the Modero panel address into the URL List in NetLinx
Studio and set the connection mode to Listen. This mode allows the Modero touch
panel to "listen" for the Master’s communication signals.
The System Number and Master IP/URL fields are red-only.
• Auto - In this mode, enter the System Number and a username/password (if
applicable). This mode is used when both the panel and the NetLinx Master are on
the same Subnet and the Master has its UDP feature enabled.
The Master IP/URL field is read-only.
System Number: Allows you to enter a system number. Default value is 0 (zero).
(ETHERNET Only - disabled when USB is selected)
Master IP/URL: Sets the Master IP or URL of the NetLinx Master.
(ETHERNET Only - disabled when USB is selected)
Master Port Number: Enters the port number used with the NetLinx Master.
• Default value is 1319. (ETHERNET Only - disabled when USB is selected)
Username/Password: If the target Master has been previously secured, enter the alphanumeric string (into
each field) assigned to a pre-configured user profile on the Master.
This profile should have the pre-defined level of access/configuration rights.
Back: Saves any changes and returns to the previously active touch panel page.
- NXD-430/435/435P 1
- Table of Contents 10
- Introduction 13
- Product Specifications 14
- Common Application 16
- Features 16
- NXD-435 Specifications 17
- Side Connectors 20
- Capacitive Touch Buttons 20
- Installation 21
- RJ-45 wiring diagram 30
- PS-POE-AF PoE Injector 31
- Panel Calibration 33
- Touch Panel Calibrate Screens 34
- Configuring Communication 35
- System Settings page 37
- USB Properties windows 40
- 2. Open the IP tab (FIG. 30) 44
- Connection Details dialog 52
- Upgrading Modero Firmware 53
- Protected Setup button 54
- Setup Pages and Descriptions 59
- Connection Status Icon 60
- Display Page (Cont.) 61
- Audio Page 61
- Panel Information 62
- Protected Setup 65
- Date/Time Page 66
- Set Time Page 67
- Protected Setup Page 68
- Protected Setup Page (Cont.) 69
- Security Settings 71
- System Settings Page 72
- System Settings Page - IP Tab 72
- System Settings - Master Tab 74
- System Settings - USB Tab 75
- Calibrate Page 76
- G4 Web Control Page 77
- Password Page 79
- Panel Statistics Page 80
- Panel Statistics - ICSP Tab 80
- Connection Utility 83
- Programming 85
- Page Commands (Cont.) 86
- Font Styles and ID Numbers 92
- TPD4 Border Styles by Name 93
- Text Effects 113
- Button Query Commands 114
- Button Query Commands (Cont.) 116
- Panel Runtime Operations 123
- Input Commands 127
- Embedded Codes 128
- Panel Setup Commands 129
- Dynamic Image Commands 130
- ^RAF, ^RMF - Embedded Codes 131
- Embedded Code 132
- ’%R <refresh 1-65535>’ 132
- ’%N <0-1>’ 132
- ’%V <0-1>’ 132
- Troubleshooting 133
- Appendix A - Text Formatting 137
- Text Area Input Masking 138
- Input Mask Ranges 139
- Input Mask Operations 139
- Input Mask Literals 139
- URL Resources 140
- Special Escape Sequences 141
- Overview 143
Related products and manuals for Touch screen monitors AMX NXD-430-WH
Touch screen monitors AMX NXT-CV7 Specifications
(220 pages)
(220 pages)
Touch screen monitors AMX NXT-CA7 Specifications
(152 pages)
(152 pages)
© 2020, manymanuals.com. All rights reserved. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals