AMX RADIA LIGHTING CONTROL ENCLOSURE WORKSHEET GUIDE Specifications Page 37
- Page / 80
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
5. Routine Operations
Rain Bird
®
ET Manager Series - Installation and Operation Manual 37
Actions to take:
1. Check when the last weather signal was
received by your ET Manager.
Main Menu
Information Log
Weather Signal
2. Check the Accuracy percentage of the weather
signal.
Main Menu
Information Log Weather
Signal
3. Verify the weather region in your ET Manager
is programmed correctly. Navigate the menus
to the Data Source screen to view the pro-
grammed weather region.
Main Menu
Settings System
Data Source Weather Region
4. If the Weather Region number is programmed
incorrectly, press À to move the cursor loca-
tion to the number and use the
Œ or Õ to
change the weather region number.
5. If you continue to have the No Weather Data
message, contact your WRSP or call Rain Bird
Technical Services at 1-877-351-6588 to verify
that no weather data is being sent.
Note: In the Automatic Control Mode, when weather
signals are missed the ET Manager will automatically
calculate ET for the missed signals. Even though sig-
nals are missed, the ET Manager will continue to oper-
ate. If weather signals are not received for more than a
day then the ET Manager will calculate ET based on
weather data from the last 7 days. If there is no weather
signal received for more than a week, the mode auto-
matically uses the pre-programmed Historical ET val-
ues.
No Paging Signal
Your ET Manager is programmed to a specific Signal
Provider Code to receive the weather signal.
Commercial wireless paging systems carry the wireless
weather signal. The ET Manager regularly verifies the
presence of the weather signal. If the weather signal is
not detected after a period of time the Attention
Indicator Light comes on and the “No Paging Signal” is
displayed.
Actions to take: If this Attention condition occurs,
wait two minutes to ensure the weather signal will not
be detected within the next few minutes. If the
Attention message remains, follow these steps:
1. Navigate the menus to the Weather Signal
screen.
Main Menu
Information Log
Weather Signal
2. Press
À to reset the pager.
Main Menu
Information Log
Weather Signal Reset
3. Monitor the Accuracy percentage and the Test
Counter. Should these values increase, the
paging signal may have been restored.
4. If the Signal changes from “Not Detected” to
“Detected,” your paging signal is restored. If it
remains “Not Detected,” continue to step 5.
5. Verify the Signal Provider Code is programmed
correctly. If the Signal Provider Code is pro-
grammed incorrectly, use the
Œ, Õ and À
buttons to set the codes for A through J.
Main Menu Settings System
Data Source Signal Provider Code
Note: To obtain your Signal Provider Code, contact
your WRSP, the Rain Bird Distributor, your installa-
tion contractor, or go to
www.rainbird.com/etmanager. Refer to chapter 3,
Programming, for more information on the Signal
Provider Code setting.
- ET Manager Series 1
- Table of Contents 2
- 1. Introduction 3
- The Weather Reach Water 4
- Management System 4
- Getting to Know your 5
- Rain Bird ET Manager 5
- LCD Contrast 6
- Attention Indicator Light 6
- Specifications 7
- Resource CD Included with 8
- Getting Ready to use 8
- Your ET Manager 8
- Mounting 10
- Wire Connections 11
- 4” insulation off the ends 12
- Wiring Diagrams 13
- Optional Rain Gauge 13
- 2. Installation 14
- Optional External Antenna 15
- Install Battery 16
- 3. Programming 17
- Weather Region 18
- Rain Source 18
- Elevation 18
- Signal Provider Code 18
- 2. Output Method 19
- Output Method 19
- 3. Site Specific Settings 19
- Irrigation Control 19
- Weather Interrupt 23
- System Options 24
- Programming the Sprinkler 25
- Controller 25
- Cycle Start Times 26
- Station Run Times 26
- 4. System Check 27
- Override 28
- Weather Signal Test 28
- Valve Control Test 29
- Water Window Settings 29
- Initial Moisture Levels 29
- 5. Routine Operation 30
- Irrigation Status 31
- 5. Routine Operations 32
- Information Log 33
- Status Messages 34
- Attention Messages 35
- No Paging Signal 37
- Signal Accuracy 38
- No Historical ET Data 39
- Decoder Failure 39
- No Watering Detected 39
- Rain Tip Input Failure 39
- Set Signal Provider Code 40
- Window Overlaps Off Day 40
- 6. Determining 41
- Programmable Settings 41
- Rain Bird 42
- Landscape Conditions 43
- Plant Type 43
- Soil Type 43
- Root Depth 43
- ET Manager Settings 44
- Water Window 45
- Available Days 46
- Advanced Settings 46
- Effective Rain Settings 46
- ET Manager Scheduler 47
- 7. Troubleshooting 48
- Water Management 49
- Troubleshooting 49
- Group are too dry or too wet 50
- 8. Advanced Output Methods 53
- Wiring “A Then B” 54
- ET & Rain Pulse 55
- Wiring ET and Rain Pulse 56
- Using More than One Sprinkler 59
- 9. Appendices 60
- Precipitation Rate 65
- Station Run Time 65
- Master Valve Control 70
- Pump Control 72
- 10. Glossary 73
- The Intelligent Use of Water 80
© 2020, manymanuals.com. All rights reserved. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals