AMX DXLink Multi-Format Wallplate Instruction Manual Page 67
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Network Configuration
67
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
Device IDs
Using the ID Pushbutton
The ID Pushbutton is located on the right front of the modules, on the left edge of the Wallplate TX, and on the front of
the Decor Wallplate TX.
The ID Pushbutton can be used to perform four types of initial configuration settings:
Toggle between DHCP and static IP addressing (see below)
Assign a device address (page 68)
Reset the unit to its factory default settings, which affects the parameters but not the firmware version (see
page 69)
Restore the unit to its factory firmware image, which affects both the firmware version and the parameters
(see page 70)
The functions performed depend on when and for how long the ID Pushbutton is pressed and held. ID Pushbutton
functions can also be implemented using Telnet commands (see page 108).
Tip: To monitor the ID Pushbutton boot state of a module by its NetLinx LED behavior, see page 71.
Toggling Between IP Addressing Modes: DHCP and Static IP
DXLink Transmitters and Receivers support both DHCP and static IP addresses. When the #3 Toggle is ON (see
page 45), the modules automatically use DHCP with link-local fallback. However, you can use a static IP address which
can be set via a Telnet command (SET IP), or you can use the factory default static IP address. The default static
IP address can be recalled at any time by resetting the unit to its factory default configuration (see page 69). The default
dynamic (DHCP) address is 169.254.2.2.
The ID Pushbutton can be used to toggle between the DHCP and Static IP Modes.
To toggle between DHCP and Static IP Modes:
1.
Once the module has booted up, press and hold the ID Pushbutton until the Control/NetLinx LEDs toggle back and
forth in unison approximately 10 times.
2. Release when it starts to blink faster.
When the Pushbutton is released, the module toggles either from static to dynamic (DHCP) IP addressing or
vice versa and remains in that mode until the ID Pushbutton is used to set it again or a factory reset is
performed.
The module automatically reboots to complete the process.
Device IDs
Model ID (16-bits) Bound ID (16-bits) Unbound
HDMI-TX Module (AVB-TX-HDMI-DXLINK) 0x017C 0x014B
Multi-Format TX Module (AVB-TX-MULTI-DXLINK) 0x017F 0x014B
Multi-Format Wallplate TX (AVB-WP-TX-MULTI-DXLINK) 0x017E 0x014B
Decor Wallplate TX (AVB-DWP-TX-MULTI-DXLINK) 0x018B ______
HDMI-RX Module (AVB-RX-DXLINK-HDMI) 0x017D 0x014B
FIG. 37
ID Pushbutton on module (HDMI TX shown)
ID Pushbutton
- Twisted Pair 1
- Transmitters/Receiver 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Warnings and Cautions 10
- Applicability Notice 11
- Product Notes 11
- Product Compatibility Tables 12
- Multi-Format TX front view 14
- HDMI TX front view 14
- Multi-Format TX rear view 18
- HDMI TX rear view 19
- Receiver 22
- HDMI RX front view 22
- HDMI RX rear view 23
- Common Features/Functionality 25
- USB Port (Rear) 26
- Shielded Cat6, Cat6A, Cat7* 31
- qualified): 1 per module 32
- Audio Format 33
- Local Audio 35
- Specifications 35
- Installation and Setup 36
- Setup Information 37
- Custom EDID Settings 38
- Example B 40
- Example C 40
- Example D 40
- Example A 40
- Power Budget Calculation 42
- Avoid network loops 43
- #1 Toggle Settings 44
- Installation Options 44
- #2 Toggle Settings 44
- #3 Toggle Settings 45
- V Style mounting hardware 46
- DXLink LEDs 51
- Audio Type Precedence 52
- Control Cables 55
- HDMI RX – Applying Power 58
- IR Receiver cable (FG-IR03) 60
- ID Pushbutton Functions 61
- Network Configuration 64
- TCP/IP Address Configuration 65
- Factory Default Parameters 66
- Device IDs 67
- Using the ID Pushbutton 67
- Factory Parameters* 69
- IRL File Transfers 72
- Transferring IRL Files 75
- Additional Documentation 77
- Overview 78
- Device Numbering and Ports 78
- Aspect Ratio Options 82
- VIDIN_PREF_EDID 85
- IR CHANNELs 88
- IR SEND_COMMANDs 88
- GET MODE 89
- SET MODE (IR command) 90
- USB SEND-COMMANDs (Receiver) 94
- FACTORYAV command 96
- SET TELNET PORT 97
- Troubleshooting 99
- Power Issues 100
- DXLink Connection Issues 101
- Network Setup Issues 102
- Technical Support 102
- Extender System (Standalone) 103
- Important Upgrade Information 105
- Firmware Versions 106
- Transferring KIT Files 107
- Telnet Username and Password 109
- Telnet Commands (continued) 111
- Master Connection Modes 116
- Windows Client Programs 117
- Linux Telnet Client 117
- Creating a Virtual Master 120
- Click to open the 120
- Communication Settings 120
- CONNECTION and press Enter 122
- HD-15 Connector Cable Pinout 124
- DVI Connector Pinout 125
- CEA (RGB Color Space): 130
- CVR (RGB Color Space): 131
- CVT (RGB Color Space): 132
- DMR (RGB Color Space): 133
- DMT (RGB Color Space): 133
- Applicability 134
- Remove jackscrew and washer 135
- Appendix H – EDID Programming 136
- DXLink Connection to PC 137
- EDID Programmer View 138
- Read Error Message 139
- 01/07/14 141
Related products and manuals for Receiver AMX DXLink Multi-Format Wallplate
Receiver AMX UDM-0102 User Manual
(3 pages)
(3 pages)
Receiver AMX UDM-0102 User Manual
(2 pages)
(2 pages)
Receiver AMX MX8 Instruction Manual
(22 pages)
(22 pages)
Receiver AMX DXLink HDMI User Manual
(6 pages)
(6 pages)
Receiver AMX MX16 User Manual
(2 pages)
(2 pages)
Receiver AMX MX8 User Manual
(2 pages)
(2 pages)
(6 pages)© 2020, manymanuals.com. All rights reserved. | 1.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals