AMX DXLink Multi-Format Wallplate Instruction Manual Page 65
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Network Configuration
65
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
When in DHCP Mode (the default setting), the module will attempt to get a DHCP lease (consisting of an IP address,
gateway, and other network parameters). Should the attempt fail, the module will then configure itself for a link-local
address.
DXLink Modules utilize a modified link-local addressing procedure. The first address to be tried is a known
address in the link-local space: 169.254.2.2. That address will be probed, and if unclaimed will be used by the
DXLink Module.
If 169.254.2.2 is already claimed, the DXLink Module will choose a random address within the 169.254.x.x
link-local address space (again probing to ensure that it is unclaimed).
Once the module is operating with a link-local address, it will periodically re-try DHCP and re-assign the IP to a valid
DHCP grant if successful.
At any time, if the module determines that its IP address has changed, it will disconnect from the Master (if necessary,
depending on the connection state) and then reconnect to the Master.
TCP/IP Address Configuration
DXLink Modules support IPV4 network addresses, gateway addresses, DNS server addresses, and network names. They
also support NDP (NetLinx Discovery Protocol) capabilities as well as IP discovery via NetLinx Studio.
Note: NDP is a device discovery method used by NetLinx Masters. With NDP Beacon enabled, the Master
will transmit NDP Beacons for AMX’s proprietary device discovery.
Telnet IP Configuration Commands
The SET IP and GET IP Telnet commands listed in the tables in Appendix B (which start on page 109) can be sent
directly to the device via a Telnet terminal session. These commands can be used for initial network configuration of the
DXLink Modules.
The default Telnet port is 23.
Telnet is enabled by default.
A value of 0 disables the telnet server.
For details, see “Appendix B – Telnet (Terminal) Commands” on page 108. The appendix also includes a section on
“Master Connection Modes” on page 116.
- Twisted Pair 1
- Transmitters/Receiver 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Warnings and Cautions 10
- Applicability Notice 11
- Product Notes 11
- Product Compatibility Tables 12
- Multi-Format TX front view 14
- HDMI TX front view 14
- Multi-Format TX rear view 18
- HDMI TX rear view 19
- Receiver 22
- HDMI RX front view 22
- HDMI RX rear view 23
- Common Features/Functionality 25
- USB Port (Rear) 26
- Shielded Cat6, Cat6A, Cat7* 31
- qualified): 1 per module 32
- Audio Format 33
- Local Audio 35
- Specifications 35
- Installation and Setup 36
- Setup Information 37
- Custom EDID Settings 38
- Example B 40
- Example C 40
- Example D 40
- Example A 40
- Power Budget Calculation 42
- Avoid network loops 43
- #1 Toggle Settings 44
- Installation Options 44
- #2 Toggle Settings 44
- #3 Toggle Settings 45
- V Style mounting hardware 46
- DXLink LEDs 51
- Audio Type Precedence 52
- Control Cables 55
- HDMI RX – Applying Power 58
- IR Receiver cable (FG-IR03) 60
- ID Pushbutton Functions 61
- Network Configuration 64
- TCP/IP Address Configuration 65
- Factory Default Parameters 66
- Device IDs 67
- Using the ID Pushbutton 67
- Factory Parameters* 69
- IRL File Transfers 72
- Transferring IRL Files 75
- Additional Documentation 77
- Overview 78
- Device Numbering and Ports 78
- Aspect Ratio Options 82
- VIDIN_PREF_EDID 85
- IR CHANNELs 88
- IR SEND_COMMANDs 88
- GET MODE 89
- SET MODE (IR command) 90
- USB SEND-COMMANDs (Receiver) 94
- FACTORYAV command 96
- SET TELNET PORT 97
- Troubleshooting 99
- Power Issues 100
- DXLink Connection Issues 101
- Network Setup Issues 102
- Technical Support 102
- Extender System (Standalone) 103
- Important Upgrade Information 105
- Firmware Versions 106
- Transferring KIT Files 107
- Telnet Username and Password 109
- Telnet Commands (continued) 111
- Master Connection Modes 116
- Windows Client Programs 117
- Linux Telnet Client 117
- Creating a Virtual Master 120
- Click to open the 120
- Communication Settings 120
- CONNECTION and press Enter 122
- HD-15 Connector Cable Pinout 124
- DVI Connector Pinout 125
- CEA (RGB Color Space): 130
- CVR (RGB Color Space): 131
- CVT (RGB Color Space): 132
- DMR (RGB Color Space): 133
- DMT (RGB Color Space): 133
- Applicability 134
- Remove jackscrew and washer 135
- Appendix H – EDID Programming 136
- DXLink Connection to PC 137
- EDID Programmer View 138
- Read Error Message 139
- 01/07/14 141
Related products and manuals for Receiver AMX DXLink Multi-Format Wallplate
Receiver AMX UDM-0102 User Manual
(3 pages)
(3 pages)
Receiver AMX UDM-0102 User Manual
(2 pages)
(2 pages)
Receiver AMX MX8 Instruction Manual
(22 pages)
(22 pages)
Receiver AMX DXLink HDMI User Manual
(6 pages)
(6 pages)
Receiver AMX MX16 User Manual
(2 pages)
(2 pages)
Receiver AMX MX8 User Manual
(2 pages)
(2 pages)
(6 pages)© 2020, manymanuals.com. All rights reserved. | 0.708 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals