AMX DXLink Multi-Format Wallplate Instruction Manual Page 100
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting
100
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
Power Issues
Upon power up, the Power indicator LED on the front of the DXLink units illuminates solid green.
If the Power LEDs on any of the system’s equipment are not illuminated:
Check the power cords or DXLink (RJ-45) connection if using power over the DXLink line.
Check the power connections on the switcher if using power over the DXLink line.
Check the power connections on the source and destination devices.
DXLink Power Delivery Issues
Unexpected power interruptions of DXLink Transmitters and Receivers may be caused by the Enova DGX Digital
Media Switcher being powered by single phase power. Connecting a ground wire to the DXLink unit’s chassis and a
common earthed ground (ideally, referenced to the switcher) will stop power interruptions. For information on when and
how to attach ground wires to DXLink units, see page 47.
Important Power Considerations for Enova DGX Endpoint Systems
Local power – Local power (the desktop power supply) always takes precedence over power via the DXLink
line from the switcher. However, if a locally powered module is connected to a switcher and the local power
is lost (i.e., unplugged or turned off), the module will power down and then automatically power back up
using power from the switcher via the DXLink connection (increasing the overall power draw on the
switcher). When local power is restored, it automatically replaces the power over the DXLink line.
DXLink power – When Transmitters/Receivers are being powered by an Enova DGX DXLink board or
DXLink power injector (using power via the DXLink line), to maintain the switcher’s power redundancy, we
recommend that you:
Determine the power budget based on the Input/Output boards used and the quantity
of powered endpoints (Transmitters/Receivers); see page 56.
Do not use the local DC power jack on the module (even if the local power adapter
is turned off).
Power Issues with Enova DGX Endpoint Systems
In an Enova DGX Endpoint System when multiple endpoints (Transmitters/Receivers) cycle their power and the
DXLink connection fails, check the following:
Check to be sure that Transmitters/Receivers being powered by the local DC jack have power. (Local
power always takes precedence.)
Check to be sure that Transmitters/Receivers intended to be powered via the DXLink line do not have a
DC jack plugged in (even if the local power adapter is turned off). This can cause inadvertent ground
loops that can negatively affect DXLink power sensing circuits.
- Twisted Pair 1
- Transmitters/Receiver 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Warnings and Cautions 10
- Applicability Notice 11
- Product Notes 11
- Product Compatibility Tables 12
- Multi-Format TX front view 14
- HDMI TX front view 14
- Multi-Format TX rear view 18
- HDMI TX rear view 19
- Receiver 22
- HDMI RX front view 22
- HDMI RX rear view 23
- Common Features/Functionality 25
- USB Port (Rear) 26
- Shielded Cat6, Cat6A, Cat7* 31
- qualified): 1 per module 32
- Audio Format 33
- Local Audio 35
- Specifications 35
- Installation and Setup 36
- Setup Information 37
- Custom EDID Settings 38
- Example B 40
- Example C 40
- Example D 40
- Example A 40
- Power Budget Calculation 42
- Avoid network loops 43
- #1 Toggle Settings 44
- Installation Options 44
- #2 Toggle Settings 44
- #3 Toggle Settings 45
- V Style mounting hardware 46
- DXLink LEDs 51
- Audio Type Precedence 52
- Control Cables 55
- HDMI RX – Applying Power 58
- IR Receiver cable (FG-IR03) 60
- ID Pushbutton Functions 61
- Network Configuration 64
- TCP/IP Address Configuration 65
- Factory Default Parameters 66
- Device IDs 67
- Using the ID Pushbutton 67
- Factory Parameters* 69
- IRL File Transfers 72
- Transferring IRL Files 75
- Additional Documentation 77
- Overview 78
- Device Numbering and Ports 78
- Aspect Ratio Options 82
- VIDIN_PREF_EDID 85
- IR CHANNELs 88
- IR SEND_COMMANDs 88
- GET MODE 89
- SET MODE (IR command) 90
- USB SEND-COMMANDs (Receiver) 94
- FACTORYAV command 96
- SET TELNET PORT 97
- Troubleshooting 99
- Power Issues 100
- DXLink Connection Issues 101
- Network Setup Issues 102
- Technical Support 102
- Extender System (Standalone) 103
- Important Upgrade Information 105
- Firmware Versions 106
- Transferring KIT Files 107
- Telnet Username and Password 109
- Telnet Commands (continued) 111
- Master Connection Modes 116
- Windows Client Programs 117
- Linux Telnet Client 117
- Creating a Virtual Master 120
- Click to open the 120
- Communication Settings 120
- CONNECTION and press Enter 122
- HD-15 Connector Cable Pinout 124
- DVI Connector Pinout 125
- CEA (RGB Color Space): 130
- CVR (RGB Color Space): 131
- CVT (RGB Color Space): 132
- DMR (RGB Color Space): 133
- DMT (RGB Color Space): 133
- Applicability 134
- Remove jackscrew and washer 135
- Appendix H – EDID Programming 136
- DXLink Connection to PC 137
- EDID Programmer View 138
- Read Error Message 139
- 01/07/14 141
Related products and manuals for Receiver AMX DXLink Multi-Format Wallplate
Receiver AMX UDM-0102 User Manual
(3 pages)
(3 pages)
Receiver AMX UDM-0102 User Manual
(2 pages)
(2 pages)
Receiver AMX MX8 Instruction Manual
(22 pages)
(22 pages)
Receiver AMX DXLink HDMI User Manual
(6 pages)
(6 pages)
Receiver AMX MX16 User Manual
(2 pages)
(2 pages)
Receiver AMX MX8 User Manual
(2 pages)
(2 pages)
(6 pages)© 2020, manymanuals.com. All rights reserved. | 0.871 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals