AMX DXLink Multi-Format Wallplate Instruction Manual Page 37
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Setup
37
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
Unpacking Tips
Before fully unpacking the Transmitters and Receivers, inspect the shipping box(es) for any signs of
damage. If a box is partially crushed or any sides have been broken open, notify the shipping agency
immediately and contact your AMX representative (see the warranty at www.amx.com).
Once unpacking is complete, closely check the physical condition of the units.
Collect all documentation.
Note: Please save the original shipping container and packing materials. AMX is not responsible for damage
caused by insufficient packing during return shipment to the factory. Shipping boxes are available; for details,
contact your AMX representative.
Setup Information
Setup Requirements
A PC with NetLinx Studio (v3.3 or later) installed.
An understanding of which DXLink Mode the system will be used in (see below and page 41).
An understanding of the DIP switch settings (see page 44).
When used with an Enova DGX Digital Media Switcher – The system’s power requirements must be
determined (see page 41).
When used with an Enova DVX Solution – The SEND_COMMANDs for enabling network activity (Ethernet
traffic) over the DXLink line must be used (see page 98).
Important: We recommend that DXLink equipment be installed by a technician with knowledge of networks
and experience with NetLinx Studio and its Telnet interface. NetLinx experience should include changing
device addresses, binding devices, updating firmware, etc.
The remainder of the “Setup Information” section covers information for system setup, power budget planning, network
loop concerns, DIP switch settings, mounting options, chassis grounding, cable requirements and recommendations
(including RJ-45 pinouts and LED behavior), and audio type precedence.
The specific installation’s requirements dictate the system setup, which generally takes one of the following three forms.
Endpoint Mode (Switcher) – One or more Transmitters and/or Receivers are connected to a switcher*
containing a Master (see below).
Endpoint Mode (Standalone) – A standalone DXLink TX/RX pair are connected directly to each other but,
in addition, either the TX or RX is connected to a NetLinx Central Controller via a LAN or directly to the
Controller (see page 40).
Extender Mode (Standalone) – A standalone DXLink TX/RX pair are connected directly to each other as a
simple extender solution (see page 41).
* The switcher can be either an Enova DGX Switcher or an applicable Enova DVX Solution (see “Product Compatibility
Tables” on page 12).
- Twisted Pair 1
- Transmitters/Receiver 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Warnings and Cautions 10
- Applicability Notice 11
- Product Notes 11
- Product Compatibility Tables 12
- Multi-Format TX front view 14
- HDMI TX front view 14
- Multi-Format TX rear view 18
- HDMI TX rear view 19
- Receiver 22
- HDMI RX front view 22
- HDMI RX rear view 23
- Common Features/Functionality 25
- USB Port (Rear) 26
- Shielded Cat6, Cat6A, Cat7* 31
- qualified): 1 per module 32
- Audio Format 33
- Local Audio 35
- Specifications 35
- Installation and Setup 36
- Setup Information 37
- Custom EDID Settings 38
- Example B 40
- Example C 40
- Example D 40
- Example A 40
- Power Budget Calculation 42
- Avoid network loops 43
- #1 Toggle Settings 44
- Installation Options 44
- #2 Toggle Settings 44
- #3 Toggle Settings 45
- V Style mounting hardware 46
- DXLink LEDs 51
- Audio Type Precedence 52
- Control Cables 55
- HDMI RX – Applying Power 58
- IR Receiver cable (FG-IR03) 60
- ID Pushbutton Functions 61
- Network Configuration 64
- TCP/IP Address Configuration 65
- Factory Default Parameters 66
- Device IDs 67
- Using the ID Pushbutton 67
- Factory Parameters* 69
- IRL File Transfers 72
- Transferring IRL Files 75
- Additional Documentation 77
- Overview 78
- Device Numbering and Ports 78
- Aspect Ratio Options 82
- VIDIN_PREF_EDID 85
- IR CHANNELs 88
- IR SEND_COMMANDs 88
- GET MODE 89
- SET MODE (IR command) 90
- USB SEND-COMMANDs (Receiver) 94
- FACTORYAV command 96
- SET TELNET PORT 97
- Troubleshooting 99
- Power Issues 100
- DXLink Connection Issues 101
- Network Setup Issues 102
- Technical Support 102
- Extender System (Standalone) 103
- Important Upgrade Information 105
- Firmware Versions 106
- Transferring KIT Files 107
- Telnet Username and Password 109
- Telnet Commands (continued) 111
- Master Connection Modes 116
- Windows Client Programs 117
- Linux Telnet Client 117
- Creating a Virtual Master 120
- Click to open the 120
- Communication Settings 120
- CONNECTION and press Enter 122
- HD-15 Connector Cable Pinout 124
- DVI Connector Pinout 125
- CEA (RGB Color Space): 130
- CVR (RGB Color Space): 131
- CVT (RGB Color Space): 132
- DMR (RGB Color Space): 133
- DMT (RGB Color Space): 133
- Applicability 134
- Remove jackscrew and washer 135
- Appendix H – EDID Programming 136
- DXLink Connection to PC 137
- EDID Programmer View 138
- Read Error Message 139
- 01/07/14 141
Related products and manuals for Receiver AMX DXLink Multi-Format Wallplate
Receiver AMX UDM-0102 User Manual
(3 pages)
(3 pages)
Receiver AMX UDM-0102 User Manual
(2 pages)
(2 pages)
Receiver AMX MX8 Instruction Manual
(22 pages)
(22 pages)
Receiver AMX DXLink HDMI User Manual
(6 pages)
(6 pages)
Receiver AMX MX16 User Manual
(2 pages)
(2 pages)
Receiver AMX MX8 User Manual
(2 pages)
(2 pages)
(6 pages)© 2020, manymanuals.com. All rights reserved. | 0.137 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals