AMX DXLink Multi-Format Wallplate Instruction Manual Page 19
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Product Overview and Specifications
19
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
HDMI TX Rear View (product discontinued)
Note: The Multi-Format TX and HDMI TX each have a DIP switch on the bottom (see page 25).
The following components are located on the rear of the Multi-Format TX and HDMI TX Modules (from left to
right):
Video In Connector (Multi-Format TX only)
The Video In connector on the Multi-Format TX is an HD-15 connector for analog video (composite, Y/C,
Y/Pb/Pr, RGB, RGBHV, or RGBS). Pinouts for analog video are on page 124.
Note: When an analog video source cable is plugged into the Multi-Format TX, the Video LEDs on the front
and on the Receiver turn green to show that video is present through the system. In addition, one of the
Analog Video LEDs on the front of the Multi-Format TX and the HDMI RX turns green to show the type of
video that is present through the system.
HDMI In Connector
The HDMI In connector is for digital video and embedded digital audio. When more than one audio signal is
present and the default “auto” mode is enabled, HDMI embedded audio takes precedence over S/PDIF and analog
audio.
When a NetLinx Central Controller is connected, an audio format SEND_COMMAND is available (the
Transmitter must be set for network connectivity via #3 Toggle) to select the desired audio source (see page 87).
The HDMI connector has a center screw for locking capability. The HDMI connector also supports a DVI-D
signal with the use of a DVI-to-HDMI cable adapter.
Note: When a digital video source cable is plugged into the HDMI connector, the Video LEDs on the front of
the Multi-Format TX or HDMI TX and Receiver turn green to show that video is present through the system.
Stereo Audio In Jack
The Stereo Audio In jack is a 3.5 mm stereo jack. By default, the stereo audio jack will be third in priority behind
the embedded audio on the HDMI input and digital audio on the RCA connector.
When a NetLinx Central Controller is connected, an audio format SEND_COMMAND is available (the
Transmitter must be set for network connectivity via #3 Toggle) to select the desired audio source (see page 87).
Digital Audio In Jack
The Digital Audio In jack is an RCA jack for an S/PDIF audio signal. When more than one audio signal is present
and the default “auto” mode is enabled, HDMI embedded audio takes precedence over S/PDIF, which takes
precedence over analog audio.
When a NetLinx Central Controller is connected, an audio format SEND_COMMAND is available (the
Transmitter must be set for network connectivity via #3 Toggle) to select the desired audio source (see page 87).
FIG. 6 HDMI TX rear view
IR ports
RS-232 port
HDMI In connector
Stereo Audio In jack
USB port
ICS LAN 10/100 connector
Power jack
DXLink output connector
Digital Audio In jack
Ground screw
- Twisted Pair 1
- Transmitters/Receiver 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Warnings and Cautions 10
- Applicability Notice 11
- Product Notes 11
- Product Compatibility Tables 12
- Multi-Format TX front view 14
- HDMI TX front view 14
- Multi-Format TX rear view 18
- HDMI TX rear view 19
- Receiver 22
- HDMI RX front view 22
- HDMI RX rear view 23
- Common Features/Functionality 25
- USB Port (Rear) 26
- Shielded Cat6, Cat6A, Cat7* 31
- qualified): 1 per module 32
- Audio Format 33
- Local Audio 35
- Specifications 35
- Installation and Setup 36
- Setup Information 37
- Custom EDID Settings 38
- Example B 40
- Example C 40
- Example D 40
- Example A 40
- Power Budget Calculation 42
- Avoid network loops 43
- #1 Toggle Settings 44
- Installation Options 44
- #2 Toggle Settings 44
- #3 Toggle Settings 45
- V Style mounting hardware 46
- DXLink LEDs 51
- Audio Type Precedence 52
- Control Cables 55
- HDMI RX – Applying Power 58
- IR Receiver cable (FG-IR03) 60
- ID Pushbutton Functions 61
- Network Configuration 64
- TCP/IP Address Configuration 65
- Factory Default Parameters 66
- Device IDs 67
- Using the ID Pushbutton 67
- Factory Parameters* 69
- IRL File Transfers 72
- Transferring IRL Files 75
- Additional Documentation 77
- Overview 78
- Device Numbering and Ports 78
- Aspect Ratio Options 82
- VIDIN_PREF_EDID 85
- IR CHANNELs 88
- IR SEND_COMMANDs 88
- GET MODE 89
- SET MODE (IR command) 90
- USB SEND-COMMANDs (Receiver) 94
- FACTORYAV command 96
- SET TELNET PORT 97
- Troubleshooting 99
- Power Issues 100
- DXLink Connection Issues 101
- Network Setup Issues 102
- Technical Support 102
- Extender System (Standalone) 103
- Important Upgrade Information 105
- Firmware Versions 106
- Transferring KIT Files 107
- Telnet Username and Password 109
- Telnet Commands (continued) 111
- Master Connection Modes 116
- Windows Client Programs 117
- Linux Telnet Client 117
- Creating a Virtual Master 120
- Click to open the 120
- Communication Settings 120
- CONNECTION and press Enter 122
- HD-15 Connector Cable Pinout 124
- DVI Connector Pinout 125
- CEA (RGB Color Space): 130
- CVR (RGB Color Space): 131
- CVT (RGB Color Space): 132
- DMR (RGB Color Space): 133
- DMT (RGB Color Space): 133
- Applicability 134
- Remove jackscrew and washer 135
- Appendix H – EDID Programming 136
- DXLink Connection to PC 137
- EDID Programmer View 138
- Read Error Message 139
- 01/07/14 141
Related products and manuals for Receiver AMX DXLink Multi-Format Wallplate
Receiver AMX UDM-0102 User Manual
(3 pages)
(3 pages)
Receiver AMX UDM-0102 User Manual
(2 pages)
(2 pages)
Receiver AMX MX8 Instruction Manual
(22 pages)
(22 pages)
Receiver AMX DXLink HDMI User Manual
(6 pages)
(6 pages)
Receiver AMX MX16 User Manual
(2 pages)
(2 pages)
Receiver AMX MX8 User Manual
(2 pages)
(2 pages)
(6 pages)© 2020, manymanuals.com. All rights reserved. | 1.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals