AMX NI-2000 Instruction Manual Page 24
- Page / 134
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Connections and Wiring
18
NetLinx Integrated Controllers
Using the Configuration DIP switch
1. Disconnect the power supply from the 2-pin PWR (green) connector on the rear of the NetLinx
Integrated Controller.
2. Set DIP switch positions according to the information listed in the Baud Rate Settings on the
Configuration DIP Switch and PRD Mode Settings tables.
3. Reconnect the 12 VDC power supply to the 2-pin 3.5 mm mini-Phoenix PWR connector.
Modes and Front Panel LED Blink Patterns
The following table lists the modes and blink patterns for the front panel LEDs associated with
each mode. These patterns are not evident until after the unit is powered.
Wiring Guidelines
The Integrated Controllers require 12 VDC power from a NetLinx Power Supply to operate
properly (this supply is unit dependent). The Integrated Controller connects to the power supply via
a 2-pin 3.5 mm mini-Phoenix connector.
Think of the PRD Mode (On) equating to a PC’s SAFE Mode setting. This mode
allows a user to continue powering a unit, update the firmware, and download a new
program while circumventing any problems with a currently downloaded program.
Power must be cycled to the unit after activating/deactivating this mode on the
Program Port DIP switch #1.
Modes and LED Blink Patterns
LEDs and Blink Patterns
Mode Description
STATUS
(green)
OUTPUT
(red)
INPUT
(yellow)
OS Start Starting the operating system (OS). On On On
Boot On-board Master is booting. On Off On
Contacting DHCP
server
On-board Master is contacting a DHCP
server for IP configuration information.
On Off Fast Blink
Unknown DHCP
server
On-board Master could not find the
DHCP server.
Fast Blink Off Off
Downloading Boot
firmware
Downloading Boot firmware to the
Master’s on-board flash memory.
Do not cycle power during this process!
Fast Blink Fast Blink Fast Blink
No program running There is no program loaded, or the
program is disabled.
On Normal Normal
Normal On-board Master is functioning normally. 1 blink per second Indicates
activity
Indicates
activity
This unit should only have one source of incoming power. Using more than one
source of power to the Controller can result in damage to the internal components
and a possible burn out.
Apply power to the unit only after installation is complete.
- NetLinx Integrated 1
- Controllers 1
- (http://www.openssl.org/) 2
- Table of Contents 3
- Introduction 7
- NI-2000 Specifications 8
- NI-3000 Specifications 11
- NI-4000 Specifications 16
- Installation Procedures 21
- Connections and Wiring 23
- Wiring Guidelines 24
- ICSNet RJ-45 Signals 28
- Relay Connections and Wiring 30
- ETHERNET 30
- IR / SERIAL (Ports 5-8) 32
- IR / SERIAL (Ports 9-16) 32
- 8 76 45 321 32
- Installation and Upgrading 35
- Device:Port:System (D:P:S) 36
- Compact Flash Upgrades 37
- Setting the System Value 44
- NXC-XXX 57
- 1.00.09 57
- NetLinx Security Terms 60
- WebControl Tab 61
- Security Tab 63
- Security Tab Features (Cont.) 64
- Security System Features 64
- Security tab - Add Group page 65
- Add Group Entries 65
- Add Group Entries (Cont.) 66
- Modify Group Entries 66
- Security tab - Add User page 69
- Add User Entries 69
- Modify User Entries 70
- (ex: bit length, city, etc.) 74
- System Tab 76
- Show Devices Tab 76
- Network Tab 76
- Devices or Network) 86
- SSL Certificate Procedures 87
- NetLinx Security Features 99
- <ENTER> 100
- Main Security Menu 110
- Help menu 112
- Help Menu Options 112
- Logging Into a Session 113
- Programming 115
- Program Port Commands 116
- Program Port Commands (Cont.) 117
- ESC Pass Codes 119
- RS232/422/485 Ports Channels 120
- IR / Serial Ports Channels 124
- IR RX Port Channels 124
- IR/Serial Send_Commands 124
- Input/Output Send_Commands 129
- Troubleshooting 131
- SET ETHERNET MODE 10 HALF 132
- SET ETHERNET MODE 10 FULL 132
- SET ETHERNET MODE AUTO 132
- Last Revision: 12/10/04 134
Related products and manuals for Supplementary music equipment AMX NI-2000
(42 pages)© 2020, manymanuals.com. All rights reserved. | 0.196 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals