AMX AVB-WP-TX-MULTI-DXLINK Instruction Manual Page 110
- Page / 154
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting
104
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
Network Setup Issues
The instructions below can be used for first time setup of DXLink Modules on a network with no NetLinx
Master (integrated or standalone).
Note: Before setting up the network, we recommend plugging all required Ethernet cables into the
network before applying power to the DXLink Modules.
To set the IP, connection, and device parameters on a DXLink Module:
1.
Set the DIP switch on the DXLink Module to:
#1 and #3 Toggles – ON
#2 and #4 Toggles – OFF
2. Attach the DXLink Module via its ICS LAN 10/100 port to the network or PC.
3. Power up the DXLink Module.
The DXLink Module will get a DHCP address or default to 169.254.2.2 (or if the module is in
Static IP Mode, the address will be 192.168.1.2).
4. Establish a Telnet connection to the DXLink Module and set up the network parameters using the
following three commands:
SET IP
SET CONNECTION
SET DEVICE
5. Enter REBOOT.
Note: If you cannot locate the DXLink Module in the Online Tree, you can reset the factory default by
holding the ID button during power up until the LEDs blink in unison and then releasing the ID button.
This will revert the DXLink Module to DHCP mode. Start again at Step 1 above.
Technical Support
If this manual has not satisfactorily answered your questions regarding the DXLink Transmitters and
Receivers or they are not operating as expected, please contact your AMX representative or technical
support. Have the serial numbers for the modules ready. If the modules are connected to a switcher, locate
the serial number for the switcher too.* We recommend recording the serial numbers in an easily
accessible location.
AMX Contact Information
3000 Research Drive, Richardson, TX 75082
800.222.0193
469.624.8000
Fax 469.624.7153
Technical Support 800.932.6993
www.amx.com
* When DXLink units are used in conjunction with an Enova DVX Solution, having Diagnostic Codes
ready can be helpful for technical support in analyzing problems. (Press the Status button on the Enova
DVX front panel and use the UP and DOWN navigational buttons to scroll through the menu options to
the Diagnostic Codes.)
- Twisted Pair 1
- Transmitters/Receiver 1
- Contents 3
- ESD Warning 7
- Copyright Notice 10
- Liability Notice 10
- US FCC Notice 10
- Lithium Batteries Notice 11
- Trademark Notices 11
- Warnings and Cautions 11
- Applicability Notice 13
- Product Notes 13
- Product Compatibility Tables 14
- Common Applications 16
- Transmitters 16
- Multi-Format TX front view 16
- HDMI TX front view 16
- (Blinking = #3 Toggle OFF) 17
- Multi-Format TX rear view 21
- HDMI TX rear view 21
- Receiver 24
- HDMI RX front view 24
- HDMI RX rear view 25
- Common Features/Functionality 27
- HDCP Compliance 28
- General Specifications 31
- Shielded Cat6, Cat6A, Cat7* 32
- qualified): 1 per module 33
- Audio Format 34
- Analog Video Specifications 36
- Local Audio Specifications 37
- Installation and Setup 39
- Setup Information 40
- Example B 43
- Example C 43
- Example D 43
- Example A 43
- DXLink connections 44
- Avoid network loops 46
- V Style mounting hardware 50
- ICS LAN 10/100 LEDs 54
- (modules only) 54
- NetLinx LEDs 55
- DXLink LEDs 55
- Audio Type Precedence 56
- Important: Do not 57
- Rear view 57
- Front view 57
- HDMI RX – Applying Power 62
- IR Receiver cable (FG-IR03) 64
- ID Pushbutton Functions 65
- Manual Mode 66
- DXLink Transmitter 68
- Network Configuration 69
- TCP/IP Address Configuration 70
- Factory Default Parameters 71
- Device IDs 72
- Using the ID Pushbutton 72
- LED columns 77
- IRL File Transfers 79
- Transferring IRL Files 82
- Additional Documentation 84
- Device Numbering and Ports 85
- Overview 85
- CHANNELs 87
- Aspect Ratio Options 89
- VIDIN_PREF_EDID 93
- IR SEND_COMMANDs 97
- GET MODE 98
- Serial SEND_COMMANDs 101
- DXLink System SEND_COMMANDs 104
- SEND_STRING Escape Sequences 105
- Troubleshooting 107
- Determining HDCP Compliance 108
- Power Issues 108
- DXLink Connection Issues 109
- Network Setup Issues 110
- Technical Support 110
- Extender System (Standalone) 111
- Important Upgrade Information 114
- Transferring KIT Files 115
- Telnet Username and Password 118
- Telnet Commands (continued) 120
- Master Connection Modes 125
- Windows Client Programs 126
- Linux Telnet Client 126
- Receivers is 192.168.1.2) 127
- Creating a Virtual Master 129
- Click to open the 129
- Communication Settings 129
- CONNECTION and press Enter 132
- HD-15 Connector Cable Pinout 134
- DVI-I signal is required 135
- SEND_COMMANDs 141
- CEA (RGB Color Space): 142
- CVR (RGB Color Space): 143
- CVT (RGB Color Space): 144
- DMR (RGB Color Space): 145
- DMT (RGB Color Space): 145
- Applicability 147
- Remove jackscrew and washer 148
- Appendix H – EDID Programming 149
- DXLink Connection to PC 150
- EDID Programmer View 151
- 06/20/13 154
Related products and manuals for Wall transmitters AMX AVB-WP-TX-MULTI-DXLINK
(24 pages)© 2020, manymanuals.com. All rights reserved. | 0.466 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals