AMX AVB-WP-TX-MULTI-DXLINK Instruction Manual Page 58

  • Download
  • Add to my manuals
  • Print
  • Page
    / 154
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 57
Installation and Setup
52
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
Additional Wallplate TX and Decor Wallplate TX Functionality
The following items are on left edge of Wallplate TX and on front of Decor Wallplate TX.
Reset Button
The Reset button resets the unit’s CPU (acts like a power cycle soft reboot).
Program Port
This port (USB mini-B connector) supports DGX Configuration software for programming a customer
VGA EDID.
ID Pushbutton
The ID Pushbutton places the unit in ID Mode for setting the NetLinx ID (device only) and provides
additional functionality, such as placing the unit in Static IP Mode or DHCP Mode (see page 66).
Wallplate TX and Decor Wallplate TX – Indicator LEDs
The Wallplate TX and Decor Wallplate TX receive power from a switcher through the DXLink (RJ-45)
connection to a DXLink Input Board in the switcher. They can also receive power via either PDXL-2
(FG1090-170) or PS-POE-AT-TC (FG423-84).
Important: We recommend determining the power budget to maintain power redundancy for the
system (see page 38).
Tip: If the Wallplate TX is installed in a location where it is difficult to check the LEDs on the bottom
edge, slide a white piece of paper or a small mirror under the edge to view LED status.
* The LEDs for Digital Video, Analog Video, and Audio each indicate the configured state of the connectors, not
necessarily the presence of signals through the Wallplate TX or Decor Wallplate TX.
Wallplate TX and Decor Wallplate TX Indicator LEDs
LEDs Normal Display Indicates
Digital Video
(default)
Green The Wallplate TX and Decor Wallplate TX have been configured*
to pass HDMI (for SEND_COMMAND information, see page 86)
Analog Video One of the 3 LEDs
will be Green
The Wallplate TX and Decor Wallplate TX have been configured*
to pass one of the following types of analog video (for SEND_COM-
MAND information, see page 86):
C (composite) or Y/c (two component)
Y/PB/PR or RGB (three component)
RGBHV (five component) or RGBS (four component)
Audio Green The Wallplate TX and Decor Wallplate TX have been configured*
to pass analog audio as the audio source being embedded on the
DXLink output connection (coupled with either the analog or digital
video input path); for SEND_COMMAND information, see page 90
Power Green Power (from switcher or DXLink power injector) is applied
LEDs (bottom edge of Wallplate TX)
NetLinx - L (Link) Green Active LAN connection to an AMX Network
(Blinking = #3 Toggle OFF)
NetLinx - S (Sta-
tus)
Green
Off
Speed status is 100 Mbps
Speed status is 10 Mbps
DXLink Yellow Yellow
Flashing
Off
Authenticated HDCP (handshaking has occurred successfully)
Video is active; no HDCP
No Video
DXLink Green Green DXLink connection is established
LEDs (on front of Decor Wallplate TX)
HDCP Yellow
Flashing
Off
Authenticated HDCP (handshaking has occurred successfully)
Video is active; no HDCP
No Video
DXLink Green DXLink connection is established
Status Green
Off
Speed status is 100 Mbps
Speed status is 10 Mbps
Link/Act Active LAN connection to an AMX Network
(Blinking = #3 Toggle OFF)
Page view 57
1 2 ... 53 54 55 56 57 58 59 60 61 62 63 ... 153 154

Comments to this Manuals

No comments