AMX AVB-WP-TX-MULTI-DXLINK Instruction Manual Page 61
- Page / 154
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Setup
55
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
Multi-Format TX and HDMI TX– LED Troubleshooting
If indicator LEDs for modules do not respond with a normal display as stated in table on previous page:
Check all power connections.
Check the “Detailed NetLinx (Link/Act and Status) LED Behavior” section on page 61.
Try the suggestions in the “Troubleshooting” chapter (see page 101).
For information on restoring the module’s default settings on power up, see page 68.
HDMI RX – Attaching Signal and Control Cables
Important: Before attaching cables, be sure to set DIP switch’s toggles if necessary (see page 41).
Important: Do not
use the RJ-45 connector labeled “DXLink” for connecting to a standard Ethernet
Network.
Note: Power, IR, and RS-232 ports are covered in their own sections.
To attach signal, transport, and control cables to the HDMI RX:
1.
DXLink (input) connector – Attach a twisted pair cable from the switcher (or Multi-Format TX or
HDMI TX) to the DXLink connector on the HDMI RX.
2. HDMI Out connector – Attach the HDMI cable that goes to the destination device.*
3. ICS LAN 10/100 connector (optional) – Attach a twisted pair cable from this connector to a LAN.
(For NetLinx programming information, see page 79.)
4. USB port (optional) – Connect to a hub using a USB-A cable; connect keyboard and mouse to the
hub. (This port is for sending keyboard / mouse commands to a PC.) The USB LED on the front
monitors this port. (The USB port will be supported in a future firmware upgrade.)
5. Stereo Audio Out connector (optional) – Plug the audio cable (that goes to the audio destination)
into the stereo audio jack. For audio precedence information, see page 50. For information on audio
SEND_COMMANDs (including enabling the analog audio format), see page 84.
* DVI cable can be used instead (via a DVI-to-HDMI cable adapter); however, the advanced audio
support from HDMI will not be available.
Note: The ID Pushbutton places the HDMI RX in ID Mode for setting the NetLinx ID (device only)
and provides additional functionality, such as placing the device in Static IP Mode or DHCP Mode.
For information, see page 66.
Tip: If scaling adjustments are necessary, use SEND_COMMANDs (see page 79). If connected to
an Enova DGX output, use DGX Configuration Software via the switcher for scaling.
FIG. 32 Attach signal and control cables to HDMI RX
USB port
HDMI Out connector
DXLink input connector
Stereo audio port
ICS LAN 10/100 connector
- Twisted Pair 1
- Transmitters/Receiver 1
- Contents 3
- ESD Warning 7
- Copyright Notice 10
- Liability Notice 10
- US FCC Notice 10
- Lithium Batteries Notice 11
- Trademark Notices 11
- Warnings and Cautions 11
- Applicability Notice 13
- Product Notes 13
- Product Compatibility Tables 14
- Common Applications 16
- Transmitters 16
- Multi-Format TX front view 16
- HDMI TX front view 16
- (Blinking = #3 Toggle OFF) 17
- Multi-Format TX rear view 21
- HDMI TX rear view 21
- Receiver 24
- HDMI RX front view 24
- HDMI RX rear view 25
- Common Features/Functionality 27
- HDCP Compliance 28
- General Specifications 31
- Shielded Cat6, Cat6A, Cat7* 32
- qualified): 1 per module 33
- Audio Format 34
- Analog Video Specifications 36
- Local Audio Specifications 37
- Installation and Setup 39
- Setup Information 40
- Example B 43
- Example C 43
- Example D 43
- Example A 43
- DXLink connections 44
- Avoid network loops 46
- V Style mounting hardware 50
- ICS LAN 10/100 LEDs 54
- (modules only) 54
- NetLinx LEDs 55
- DXLink LEDs 55
- Audio Type Precedence 56
- Important: Do not 57
- Rear view 57
- Front view 57
- HDMI RX – Applying Power 62
- IR Receiver cable (FG-IR03) 64
- ID Pushbutton Functions 65
- Manual Mode 66
- DXLink Transmitter 68
- Network Configuration 69
- TCP/IP Address Configuration 70
- Factory Default Parameters 71
- Device IDs 72
- Using the ID Pushbutton 72
- LED columns 77
- IRL File Transfers 79
- Transferring IRL Files 82
- Additional Documentation 84
- Device Numbering and Ports 85
- Overview 85
- CHANNELs 87
- Aspect Ratio Options 89
- VIDIN_PREF_EDID 93
- IR SEND_COMMANDs 97
- GET MODE 98
- Serial SEND_COMMANDs 101
- DXLink System SEND_COMMANDs 104
- SEND_STRING Escape Sequences 105
- Troubleshooting 107
- Determining HDCP Compliance 108
- Power Issues 108
- DXLink Connection Issues 109
- Network Setup Issues 110
- Technical Support 110
- Extender System (Standalone) 111
- Important Upgrade Information 114
- Transferring KIT Files 115
- Telnet Username and Password 118
- Telnet Commands (continued) 120
- Master Connection Modes 125
- Windows Client Programs 126
- Linux Telnet Client 126
- Receivers is 192.168.1.2) 127
- Creating a Virtual Master 129
- Click to open the 129
- Communication Settings 129
- CONNECTION and press Enter 132
- HD-15 Connector Cable Pinout 134
- DVI-I signal is required 135
- SEND_COMMANDs 141
- CEA (RGB Color Space): 142
- CVR (RGB Color Space): 143
- CVT (RGB Color Space): 144
- DMR (RGB Color Space): 145
- DMT (RGB Color Space): 145
- Applicability 147
- Remove jackscrew and washer 148
- Appendix H – EDID Programming 149
- DXLink Connection to PC 150
- EDID Programmer View 151
- 06/20/13 154
Related products and manuals for Wall transmitters AMX AVB-WP-TX-MULTI-DXLINK
(24 pages)© 2020, manymanuals.com. All rights reserved. | 1.649 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals