AMX AVB-WP-TX-MULTI-DXLINK Instruction Manual Page 66
- Page / 154
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Setup
60
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
Manual Mode
Manual Mode allows the user to configure the resolution that the video will display through a destination
device. Manual Mode defaults to 1280x1024p @ 60 Hz. This default resolution can be changed in two
ways:
Use the SEND_COMMAND VIDOUT_RES_REF to set the resolution and refresh rate
(for details, see page 81).
When used as a direct output of an Enova DGX DXLink Output Board, use DGX
Configuration Software to set and persist the Manual scaling resolution for the connector on
the DXLink Output Board; the DXLink Output Board sends the scaling resolution data to the
HDMI RX.
Note: The scaling mode (and the aspect ratio) can also be set on the DXLink Output Board using
DGX Configuration Software. The data is persisted on the board and sent to the HDMI RX.
Persistence of Scaling Options
The HDMI RX defaults to “Auto” when power is cycled. The scaling option can be persisted using one
of the three following methods:
Using the Scaling button (see instructions below).
Using the SEND_COMMAND: PERSISTAV (for details, see page 98).
Using DGX Configuration Software to set and persist the scaling option for the connector on
the DXLink Output Board on the Enova DGX Digital Media Switcher; the DXLink Output
Board sends the scaling option data to the HDMI RX.
Using the Scaling Button to Persist a Scaling Option
The factory default is for the HDMI RX to revert to the Auto option if power is cycled. If you want the
unit to remain in either Manual or Bypass Mode when power is cycled, use the following instructions.
To persist a scaling option on power cycle:
1.
Press and release the Scaling button until the LEDs cycle to the option immediately before the one
you want to persist.
2. Press and hold the Scaling button about 5 seconds until the desired LED blinks green (indicating
that option will persist on power cycle), then release.
- Twisted Pair 1
- Transmitters/Receiver 1
- Contents 3
- ESD Warning 7
- Copyright Notice 10
- Liability Notice 10
- US FCC Notice 10
- Lithium Batteries Notice 11
- Trademark Notices 11
- Warnings and Cautions 11
- Applicability Notice 13
- Product Notes 13
- Product Compatibility Tables 14
- Common Applications 16
- Transmitters 16
- Multi-Format TX front view 16
- HDMI TX front view 16
- (Blinking = #3 Toggle OFF) 17
- Multi-Format TX rear view 21
- HDMI TX rear view 21
- Receiver 24
- HDMI RX front view 24
- HDMI RX rear view 25
- Common Features/Functionality 27
- HDCP Compliance 28
- General Specifications 31
- Shielded Cat6, Cat6A, Cat7* 32
- qualified): 1 per module 33
- Audio Format 34
- Analog Video Specifications 36
- Local Audio Specifications 37
- Installation and Setup 39
- Setup Information 40
- Example B 43
- Example C 43
- Example D 43
- Example A 43
- DXLink connections 44
- Avoid network loops 46
- V Style mounting hardware 50
- ICS LAN 10/100 LEDs 54
- (modules only) 54
- NetLinx LEDs 55
- DXLink LEDs 55
- Audio Type Precedence 56
- Important: Do not 57
- Rear view 57
- Front view 57
- HDMI RX – Applying Power 62
- IR Receiver cable (FG-IR03) 64
- ID Pushbutton Functions 65
- Manual Mode 66
- DXLink Transmitter 68
- Network Configuration 69
- TCP/IP Address Configuration 70
- Factory Default Parameters 71
- Device IDs 72
- Using the ID Pushbutton 72
- LED columns 77
- IRL File Transfers 79
- Transferring IRL Files 82
- Additional Documentation 84
- Device Numbering and Ports 85
- Overview 85
- CHANNELs 87
- Aspect Ratio Options 89
- VIDIN_PREF_EDID 93
- IR SEND_COMMANDs 97
- GET MODE 98
- Serial SEND_COMMANDs 101
- DXLink System SEND_COMMANDs 104
- SEND_STRING Escape Sequences 105
- Troubleshooting 107
- Determining HDCP Compliance 108
- Power Issues 108
- DXLink Connection Issues 109
- Network Setup Issues 110
- Technical Support 110
- Extender System (Standalone) 111
- Important Upgrade Information 114
- Transferring KIT Files 115
- Telnet Username and Password 118
- Telnet Commands (continued) 120
- Master Connection Modes 125
- Windows Client Programs 126
- Linux Telnet Client 126
- Receivers is 192.168.1.2) 127
- Creating a Virtual Master 129
- Click to open the 129
- Communication Settings 129
- CONNECTION and press Enter 132
- HD-15 Connector Cable Pinout 134
- DVI-I signal is required 135
- SEND_COMMANDs 141
- CEA (RGB Color Space): 142
- CVR (RGB Color Space): 143
- CVT (RGB Color Space): 144
- DMR (RGB Color Space): 145
- DMT (RGB Color Space): 145
- Applicability 147
- Remove jackscrew and washer 148
- Appendix H – EDID Programming 149
- DXLink Connection to PC 150
- EDID Programmer View 151
- 06/20/13 154
Related products and manuals for Wall transmitters AMX AVB-WP-TX-MULTI-DXLINK
(24 pages)© 2020, manymanuals.com. All rights reserved. | 0.934 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals