AMX MET-7 Specifications Page 81
- Page / 84
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
SWT Troubleshooting
77
Metreau Keypads
SWT Troubleshooting
Overview
This section provides troubleshooting for the SWT Metreau keypads (DAS-MET-6SRC and
DAS-MET-NUM).
Power Connections
Tracking down problems that are power related are somewhat easy because the unit either powers up or it
doesn’t. If it does not, there are several things to check.
1. Check to make sure you are attached to a functioning live electrical circuit. If the branch circuit is dead
check the breaker or there may be a light switch controlling the power to the outlet. If it’s on a switched
circuit try to obtain power elsewhere.
2. Ensure that both ends of each power cord are firmly seated in all of the source components.
3. If you’re plugged into power strips, check them for operation as well. Be aware these often have mini-
breakers on them and you should check to ensure that power is functioning in EACH outlet.
It is not uncommon for the inexpensive power strips to fail at one plug-in but not the others.
4. There is a power switch located at the rear of the Controller, check to see that it is in the ON or (1)
position.
5. There is a fuse beside the power switch at the back of the Controller. Remove the fuse and inspect it to see
that it is intact. If you have an ohm meter, test for continuity across the fuse (sometimes they look good,
but they’re really broken near one of the ends). If you are using a power bar they often have mini-breakers
on them, and you should check to ensure that all is well. The fuse in the rear of the Unit is a T8AL250v.
Symptom Possible Causes Section
Everything is dead Power Power
All keypads are dead Power-cabling between MRC and keypad
incorrect.
Power
(No lights) Keypad connections reversed. Keypad cabling
Some keypads ok, some dead. Cabling between MRC & keypad shorted.
Keypad connections reversed.
Defective keypad.
Defective cable.
Keypad Cabling.
Restart system.
Sources don’t work manually
or automatically
Power Power
Sources and keypads work
but no sound in zone.
Speakers not connected.
Problem between keypad and speakers.
Problem with speakers.
Volume too low.
Keypad Cabling
Source Cabling
Sources and keypads work
but no sound in zone.
RCA cables from source inserted into the
source outputs.
Source Cabling
Sources work manually but
keypads don’t control device.
Device programming incomplete. Infrared
emitter lead missing.
IR emitter lead connected to wrong device.
Programming.
Source cabling.
Restart system.
Sources power off when
selected.
Program error in ON/ OFF function. Programming
Sources don’t start playing when
selected.
Program error in device select function. Programming
- Keypads 1
- Table of Contents 3
- Metreau Keypads 4
- Navigation Wheel 11
- MET-7 Metreau 7-Button Keypad 12
- MET-13 Specifications 13
- DAS-MET-6SRC Specifications 14
- Pushbuttons 1-6 15
- DAS-MET-NUM Specifications 16
- Custom Button Installation 17
- Button Kits 18
- Custom Keypads and Buttons 19
- Metreau Keypads 20
- AxLink Device Addressing 21
- 8-position mini-DIP Switch 22
- Mounting and Installation 23
- Mounting Procedures 25
- Wiring and Connections 27
- AxLink straight-thru wiring 28
- SWT Wiring 29
- SWT wiring 30
- Pin #1 Pin #1 30
- Button Layouts 35
- Display Bargraph 36
- Supported SEND_LEVELs 36
- Supported SEND_COMMANDs 37
- 1. Open NetLinx Studio2 38
- Overview 41
- Listening To an iPod 42
- Listening To the Radio 42
- Adjusting Volume 42
- DAS-MET-6SRC 43
- Bass Level Adjust Mode 43
- Treble Level Adjust Mode 44
- Balance Adjust Mode 44
- Turning SRS Off 45
- Turning Privacy Mode Off 45
- Working With Sources 46
- Turning Off All Zones 48
- Direct Access 53
- Working With Presets 55
- Recalling A Preset 56
- Working With Favorites 57
- Working With Zone Grouping 58
- Adding A Zone To Group 59
- Ungrouping All Zones 59
- Working With Alarms 60
- Setting Alarm In a Zone 61
- Keypad Lockout 62
- Unlocking A Keypad 63
- Unlocking All Keypads 63
- Using the NetLinx Module 65
- Main Pages 66
- Zone Options 67
- Change Source 67
- Device Control Pages 68
- Internal Sirius 69
- Device Control Page - DVD 70
- Device Control Page - CD 71
- Audio Server 72
- Satellite 73
- External Tuner 74
- Device Control Page - Other 75
- Setup Pages 76
- Setup - Alarms 77
- Adding an Alarm 77
- Removing an Alarm 79
- SWT Troubleshooting 81
- Zone Connection Problems 82
- No Keypad Activity 83
- Keypad Lights, No Sound 83
Related products and manuals for Remote controls AMX MET-7
Remote controls AMX DAS-DI-0406 User Manual
(17 pages)
(17 pages)
Remote controls AMX NXD-CV5 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.861 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals