Amx MIO-R1-AUDIO User Manual download pdf (Page 1)

Quick Start Guide

MIO R-1 AUDIO Tango Distributed Audio Remote Control

Overview

The MIO R-1 AUDIO (FG147-04) remote provides custom control features, contained

in an elegant handheld device, designed specifically for use with Matrix Distributed

Audio Systems using Metreau DAS-MET-6SRC keypads.

The MIO R-1 AUDIO controls up to 8 different devices or Sources.

Specifications

Installing Custom Buttons

1. Flip and turn the MIO R-1 AUDIO so that the buttons are facing away from you

and the device is upside down.

2. Holding the device in both hands, place your thumbs on the battery door and

push up to slide the battery door free.

3. Unscrew the 6 screw points indicated in FIG. 2.

4. Turn the unit over so the buttons are facing you.

5. Lift the top assembly away from the PCB.

6. If necessary, push out the standard buttons from the front of the top assembly.

7. Drop on your custom button pad and verify the alignment with the guide posts on

the PCB.

8. Place the top assembly back down on the PCB and return the unit over, expos-

ing the 6 screw points.

9. Tighten the 6 screw points.

10. Place the battery door back on the device, slide to lock it in place.

Inserting Batteries into The MIO R-1 AUDIO

To install your 4 AAA batteries into the MIO R-1 AUDIO:

1. Flip and turn the MIO R-1 AUDIO so that the buttons are facing away from you

and the device is upside down.

2. Holding the device in both hands, place your thumbs on the battery door and

slide the battery door free.

3. Insert the batteries as indicated inside the battery compartment.

4. Place the battery door back on the device, slide to lock it in place.

Battery Low Indicator

When the battery charge level is too low to sustain continuous operation, the LCD

flashes, "Battery Low" and the device shuts down.

Programming The MIO R-1 AUDIO Using KeypadBuilder

The MIO R-1 AUDIO comes pre-customized with appropriate labels, which in most

cases should not be changed. However, if in your installation you intend to use the

MIO R-1 AUDIO with a NetLinx Controller and Metreau AxLink keypads (for more than

just Audio), you could customize your buttons in the KeypadBuilder application. The

application and documentation are available from www.amx.com.

There are a select number of Serial Commands the MIO R-1 AUDIO recognizes. For a

full list and descriptions, consult the MIO R-1 AUDIO Operation/Reference Guide.

The Programming Jack is used for communication between the device and

KeypadBuilder. The programming jack uses a three-wire, 2.5 mm stereo jack, you can

order the programming cable (FG10-817) from AMX if you do not currently possess

one. While loading your configuration file make sure the device is situated as such that

the batteries will not fall out. The load will fail if your batteries fall out during the

process. The MIO communicates at 115200 baud rate.

Refer to the MIO R-1 AUDIO Operation/Reference Guide for instructions on using the

Programming Jack to load configuration files on the MIO R-1 AUDIO.

Tone Control & SRS Setting

To access the Tone Control and SRS settings, press the TONE button. This enables

the Tone Control Mode with BASS as the first mode selected. There are 3 Tone

Control Modes available for adjustment, and 4 SRS options, as follows:

• BASS: Increase / Decrease from -10dB to +10dB (Up/Down NAV buttons)

• Treble: Increase / Decrease from -10dB to +10dB (Up/Down NAV buttons)

• Balance: Left / Right (Up NAV button = right, Down NAV button = left)

• SRS options: BASS Boost, Focus, 3D, WOW

The Source buttons on the Metreau keypad provides visual feedback as to which

mode it is currently in. The following sources will light based on the current mode:

• Source 1 = BASS

• Source 2 = Treble

• Source 3 = Balance

• Source 4 = SRS

When first entering Tone Control Mode, BASS mode is active (Source 1 LED is lit). To

move from mode to mode, select the Center NAV button. This saves the setting and

moves to the next mode.

FIG. 1

MIO R-1 AUDIO remote controller

MIO R-1 AUDIO Specifications

Power Requirements: 4 AAA Alkaline Batteries (included) - approx. 5 hours battery life

Transmission

Frequencies

AMX 38 KHz/455 KHz IR

Note: The Metreau MET-6N keypads only support 38 KHz. When used

with MET-6N keypads, the MIO R-1 AUDIO must be set to 38 KHz.

Transmission

Range (distance)

with MIO IR Receiver

• 100 feet at 38KHz

• 50 feet at 455KHz

Transmission

Range (angle)

• 140 degrees (+/-70° from perpendicular) horizontally from an axis

extending from the end of the remote.

• 40 degrees (+/-20° from perpendicular) vertically from an axis

extending from the end of the remote.

Top Components • LED - blue backlit buttons indicate device is awake

• Display (OLED) - 128 x 32 pixels, active area is 29.42mm x 7.98mm

• Pushbuttons - the power button is red backlit; the rest are blue backlit

buttons. 45 buttons; 9 custom buttons (3 macro and 6 device).

Rear Component • Programming Port - 2.5 mm stereo female conductor jack

• Battery Door

Dimensions (HWD) 9.50 x 2.00 x .74 (241.3 mm x 50.8 mm x 18.80 mm)

Weight • .45 lbs (20 kg) without batteries

• .55 lbs (25 kg) with batteries

Operating Environment: • Operating Temperature: 0° to 50° C (32° to 122° F)

• Storage Temperature: -10° to 70° C (14° to 158° F)

Included Accessories: • 4 AAA Batteries

Other AMX Equipment • DB-9 extension cable (FG10-727)

• Programming Cable - a 3 wire, 2.5 mm stereo jack (FG10-817)

• Custom engraving (FG147-01)

• MIO-RCC Kit (FG147-03K)

• MIO-RCC Charging Base (FG147-02)

• MIO-RBP Rechargeable Lithium Ion Battery (FG147-10)

• MIO Modero IR Receiver (FG5797-01xx; xx indicates color)

Power

IR Transmitting

Battery Meter

Source Select Options

44 45

Numeral Keypad

1 - Power

2 - Alarm

3 - Favorite

4 - Privacy

5 - Lock

6 - NAV Up

7 - NAV Down

8 - NAV Left

9 - NAV Right

10 - NAV Center

11 - Volume Up

12 - Volume Down

13 - NAV Up

14 - NAV Down

15 - Group

16 - Preset

26 - “ • “ (dot)

28 - Enter

41 - NAV Left

42 - Tone Controls/SRS options

43 - NAV Right

44 - NAV Up

45 - NAV Down

38 - Configuration (press and

hold with the “Dot” button (#26)

to access Configuration options)

FIG. 2 6 screwpoints (battery compartment cover removed)

1 2

Summary of Contents

Page 1 - Quick Start Guide

Quick Start GuideMIO R-1 AUDIO Tango Distributed Audio Remote ControlOverviewThe MIO R-1 AUDIO (FG147-04) remote provides custom control features, con

Page 2 - Additional Documentation

Comments to this Manuals

No comments

Amx MIO-R1-AUDIO User Manual Page 1

Browse online or download User Manual for Remote control Amx MIO-R1-AUDIO. AMX MIO-R1-AUDIO User Manual

Summary of Contents

Comments to this Manuals

Amx MIO-R1-AUDIO User Manual Page 1

Browse online or download User Manual for Remote control Amx MIO-R1-AUDIO. AMX MIO-R1-AUDIO User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Remote control Amx MIO-R1-AUDIO