AMX NXR-ZRP Specifications download pdf

Quick Start Guide

NXR-ZGW/ZRP NetLinx ZigBee Gateway and Repeater

Overview

The NXR-ZGW (FG5791-01) is an Ethernet to ZigBee wireless gateway. The

NXR-ZGW features a 10BaseT, half duplex Ethernet port capable of Power over

Ethernet (PoE), 16 Mbytes of Flash, 16 Mbytes of SDRAM, and a ZigBee

module, and is controlled via a web server interface.

The NXR-ZRP (FG5791-02) is a ZigBee wireless repeater.

Specifications

NOTE: Connection to the Repeater device from either the NXR-ZGW or the Mio

Modero

R-3 or R-4 requires download and installation to the repeater of ZigBee

Module firmware version 1.01.12, available from www.amx.com.

Things To Consider Before Starting

Several factors will help decide the best place to install NXR-ZGW and

NXR-ZRP devices. Before installing, consider the following:

Location and Antenna Direction

The best location for NXR-ZGW and NXR-ZRP devices are usually in the center

of your wireless network, with line of sight to all of your mobile devices. Try to

place the antenna in a position that can best cover your wireless network.

Normally, the higher you place the antenna, the better performance you receive.

Note: For minimal interference, try to keep any installed NXR-ZGW at least 10’

(3.048m) from any WiFi access points.

Connecting the Optional Accessory Antennas

Several accessory 2.4GHz antennas are available for use with NXR-ZGW and

NXR-ZRP devices. Each of these antennas is uniquely suited to meet a wide

variety of installation requirements.

NOTE (Mio R-3 or R-4 Users): Due to the wireless nature of the ZigBee

network, temporary interference (such as leaving a room or large objects

passing between the controller and its gateway device) may prevent a command

from reaching the NetLinx master. If this happens while increasing volume,

the master may receive the command to increase the volume but not the

command to stop increasing it. Therefore, programmers should consider

setting safeguards for volume control, either established volume limits or

FIG. 1 The NXR-ZGW Device (front and rear)

NXR-ZGW (FG5791-01) and NXR-ZRP (FG5791-02) Specifications

Power: • 10.5 - 18 VDC; (13.5 VDC nominal operation voltage)

• NXR-ZGW: Power over Ethernet (PoE) Class 2

Memory:

NXR-ZGW only:

NXR-ZRP only:

• 16 Mbytes of Flash

• 16 Mbytes of SDRAM

• 1 Megabit external memory

Radio Specifications:

Frequency

2.4GHz

Operating channels

11 - 26

Modulation

technique

DSS

Output power

Region/country specific

Coverage area 165 feet (50.2m)

Firmware/Software Specifications:

Management Built-in browser-based management with User Name/

Password authentication (NXR-ZGW only)

IP configuration Static IP or DHCP client (default is static, 192.168.1.140)

Communications • ZigBee

• TCP/IP

• The NXR-ZRP communicates with a Netlinx master via a

NXR-ZGW.

Front Components:

LEDs • PWR/STATUS - (NXR-ZGW) A green LED that blinks to

indicate the device is installed and communicating

properly. Power ON, but no master connection, is

indicated with a solid light, Power OFF is indicated with no

light. (NXR-ZRP) Power ON is indicated with a solid light.

Power OFF is indicated with no light.

• LAN - (NXR-ZGW) A green LED indicates an Ethernet

connection is established. The LED blinks to indicate both

sending and receiving information via Ethernet.

• RF - The LED is solid when end devices are connected;

end devices not connected is indicated with no LED light;

the LED blinks to indicate activity.

• ICSP - (NXR-ZRP) The LED is solid when ICSP

connection is in place with the NetLinx master.

Antenna Mount A reverse SMA connection that supports a 2.4GHz antenna.

PoE PWR

12VDC

ETHERNET

wire power connector

(Rear)

2-pin 3.5mm captive

10BaseT Modular

(RJ-45) connector

PWR/STATUS

LAN

ANT ID

(Front)

Connection LEDs

Antenna Mount ID Button

NXR-ZGW and NXR-ZRP Specifications (Cont.)

ID Button • NXR-ZGW: When used in conjunction with NetLinx Studio,

sets the device and system numbers for the NXR-ZGW.

Press and hold for approximately 30 seconds to return the

NXR-ZGW to factory default settings.

• NXR-ZRP: Press and hold for approximately 10 seconds

to return the NXR-ZRP to factory default settings.

Rear Components:

Power connector • 2-pin 3.5mm captive-wire connector

• NXR-ZGW: Power Over Ethernet (PoE) - powers the

device through the CAT5 cable. Both Power and Data can

be transmitted simultaneous through the CAT5 cable

when using the appropriate equipment.

Ethernet port 10BaseT Modular (RJ-45) connector - connects the NXR-

ZGW to your LAN and/or to connect your third party device

to the LAN when the NXR-ZGW is used as a gateway.

Certifications: NXR-ZGW:

• FCC ID: CWU-ZGW

• IC ID: 5078A-ZGW

•CE

• IEC-60950

•TELEC

NXR-ZRP:

• FCC ID: CWU-ZRD

• IC ID: 5088A-ZRD

•CE

• IEC-60590

•TELEC

Operating/Storage

Environments:

• Operating Temperature: -30°C (-22°F) to 70°C (158°F)

• Relative Humidity: 5% to 85% non-condensing; intended

for indoor use only

Dimensions (HWD):

0.91” x 2.50” x 3.42”

(23.01 mm x 63.50 mm x 86.96 mm)

Note: depth does not include antenna

Weight: • NXR-ZGW: 0.35 lbs (158.75g)

• NXR-ZRP: 0.25 lbs (113.39g)

Included

Accessories:

• Rubber feet

• Velcro mounting strip

• 2.4GHZ, MONO, RSMA, 3.5IN, 2.0DBI Antenna

(70-0012-SA)

• Power Supply (24-5791-SA)

Other AMX Products: • Mio Modero R-3 Remote (FG148-03)

• Mio Modero R-4 Remote (FG148-04)

• NXA-WAP 2403A 3 dBI Antenna (FG2255-20)

• NXA-WAP 2405A 5.5 dBI Antenna (FG2255-21)

• NXA-WAP 2413A Mounting Bracket (FG2255-24)

1 2

Summary of Contents

Page 1 - Quick Start Guide

Quick Start GuideNXR-ZGW/ZRP NetLinx ZigBee Gateway and RepeaterOverviewThe NXR-ZGW (FG5791-01) is an Ethernet to ZigBee wireless gateway. The NXR-ZGW

Page 2 - Utilities

AMX NXR-ZRP Specifications

Browse online or download Specifications for Networking AMX NXR-ZRP. AMX NXR-ZRP Specifications User Manual

Summary of Contents

More documents for Networking AMX NXR-ZRP

Comments to this Manuals

AMX NXR-ZRP Specifications

Browse online or download Specifications for Networking AMX NXR-ZRP. AMX NXR-ZRP Specifications User Manual

Summary of Contents

More documents for Networking AMX NXR-ZRP

Comments to this Manuals

Related products and manuals for Networking AMX NXR-ZRP