AMX CCD-15APS-1 Setup Guide download pdf (Page 1)

RF Plug-In Modules

Dimming Module : CCD-3PD-1

Appliance Module: CCD-15APS-1

120 V

50 / 60 Hz

Typical Power Consumption*: 0.3 W

Installation Instructions

Please Read Before Installing

Installation

Dimming Module Operation

Troubleshooting Guide

Lutron Elec tron ics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299

Print ed in the U.S.A. 1/11 P/N 044-275 Rev. A

Load Specifications:

Control Load Type Min. Load Max. Load

3PD-1

Incandescent, Halogen 10 W 300 W

MLV 10 W / VA 200 W / 300 VA

CFL, Fluorescent, ELV

(Switching Mode Only)

10 W 300 W

15APS-1 General purpose None

†

1/2 HP

††

15 A

Technical Assistance:

U.S.A. / Canada: 1.800.523.9466 Fax +1.610.282.6311

Mexico: +1.888.235.2910

Other Countries: +1.610.282.3800

24 hours a day, 7 days a week.

Important Notes

WARNING - Entrapment Hazard - To avoid the risk of entrapment,

serious injury, or death, these controls must not be used to control

equipment which is not visible from every control location or which

could create hazardous situations such as entrapment if operated accidentally.

Examples of such equipment which must not be operated by these controls

include (but are not limited to) motorized gates, garage doors, industrial doors,

microwave ovens, heating pads, etc. It is the installer’s responsibility to ensure

that the equipment being controlled is visible from every control location and that

only suitable equipment is connected to these controls. Failure to do so could

result in serious injury or death.

NOTICE: To avoid overheating and possible damage to other equipment, do

not use -3PD-1 to control motor-operated or transformer-supplied appliances or

other non-lighting loads. Always use a light bulb that remains within the wattage

rating of the light fixture.

Codes: Install in accordance with all local and national electrical codes.

Environment: Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C),

0% to 90% humidity, non-condensing. Indoor use only.

Cordset: The cordset has a plug on a 24 in (610 mm) cord and a receptacle on

a 6 in (152 mm) cord.

Cleaning: To clean, wipe with a clean damp cloth. DO NOT use any chemical

cleaning solutions.

Load Type: The -3PD-1 is designed to dim one incandescent, magnetic low-

voltage, or tungsten halogen table or floor lamp. The -3PD-1 can be configured to

switch a compact fluorescent, fluorescent, or electronic low-voltage load. Use with

lighting loads only. Do not use to control a lamp that contains an integral dimmer

or a touch lamp. For a lamp with an integral 3-way switch, the switch should be set

to full on position. The -3PD-1 may not work with dioded light bulbs. Always use

a load that complies with the Load Specifications table above. Always use a light

bulb that remains within the wattage rating of the light fixture.

The -15APS-1 is designed to switch general purpose loads (lighting, non-lighting,

motor-operated, or transformer supplied appliances). Total connected load can

not exceed 1/2 HP, or 15 A.

Low-voltage Applications: The -3PD-1 can be used with magnetic (core

and coil) low-voltage transformers in both dimming and switching modes.

Use with electronic (solid-state) low-voltage transformers in switching mode

only. Operation of a low-voltage circuit with light bulbs inoperative or removed

may result in transformer overheating and premature failure. Lutron strongly

recommends the following:

a. Do not operate low-voltage circuits without operative light bulbs in place.

b. Replace burned-out light bulbs as soon as possible.

c. Use transformers that incorporate thermal protection or fused transformer

primary windings to prevent transformer failure due to overcurrent.

RF Device Placement: RF Plug-In Modules must be located within 30 ft (9 m)

of an RF signal repeater. For systems with an RF signal repeater, RF Plug-In

Modules cannot be controlled by the system until they are programmed in a

system according to the system Setup Guide.

English

Lutron and the sunburst logo are registered trademarks and Clear Connect is a trademark of Lutron Electronics Co., Inc.

120 V 50 / 60 Hz

COOPERSBURG, PA 18036 USA

300 VA /

200 W

300 W

1. Place the Plug-In Module in a convenient and accessible

location.

2. Turn the load ON and unplug the cord from the wall outlet.

3. Plug the load cord into a Plug-In Module receptacle.

4. Insert the plug of the Plug-In Module into the wall outlet

5. Turn the Plug-In Module ON.

6. Verify operation. See Dimming Module Operation and

Appliance Module Operation.

WARNING - Shock Hazard - To avoid the risk of

electrical shock, unplug the Plug-In Module when

changing light bulbs. Changing light bulbs with the

power on could result in personal injury or death.

WARNING - Shock Hazard - To avoid the risk of

electrical shock, do not open, cut cord, or rewire the

Plug-In Module. Modification of the module can result

in personal injury or death.

NOTE: -3PD-1 contains a

POLARIZED cord set. It

has a polarized plug (one blade is wider than the other) and

receptacle (one slot is wider than the other).

The polarized plug is not intended to be mated with non-

polarized outlets (having both slots the same size).

The polarized receptacle is intended to mate with a polarized

plug in only one way (the wider slot with the wider blade).

Status LEDs (1-7)

Indicate light level; glow softly as night light when load

is OFF

Toggle Button

Press to toggle ON / OFF; double-tap for full ON; press

and hold while ON for delayed long fade to OFF.

Raise Button

Press to brighten

* Typical Power Consumption test conditions: load is off.

Lower Button

Press to dim

Use these instructions to install the model numbers listed above. For system Setup

Guide and tools visit www.lutron.com

CCD-3PD-1 (1 receptacle) CCD-15APS-1 (1 receptacle)

Plug-In Module

Plug-In Module Receptacle

Plug-In Module

Plug

120 V 50 / 60 Hz

1/2 HP 15 A

COOPERSBURG, PA 18036 USA

Status LED

Indicates load status; glows softly as night light when

load is OFF

Toggle Button

Press to toggle ON / OFF.

Appliance Module Operation

1. Tap the toggle button to turn off the load.

Press and hold the toggle and lower buttons for 3 seconds until

LED 1 flashes to enter Advanced Programming Mode (APM).

3. Tap the raise button until LED 7 flashes.

Press and hold the raise button until LEDs 1 and 3 flash.

5. Tap the toggle button once, wait 2 seconds, then tap the

toggle button again. Notice the LEDs that flash: LEDs 1 and 7

(Dimmer mode - Default), LEDs 2 and 7 (Switch mode).

6. Tap the raise button once. LEDs 2 and 7 will flash and the

module will be in switch mode.

7. Press and hold the toggle button for 6 seconds to save this

setting and exit APM.

NOTE: To change module back to dimmer mode, repeat steps

1-7 and select LEDs 1 and 7 in Step 6.

NOTE: If desired, the Dimming Module can be configured to

function as a switch for lighting loads only.

NOTE: During programming, the Plug-In Modules turn loads

ON/OFF very quickly. Unplug sensitive loads before proceeding.

Advanced Programming (Dimming Module to

switch mode)

Symptom Probable Cause and Action

Load does

not turn ON,

but LEDs on

the Plug-In

Module are ON

Load is turned OFF

• Turn the power switch on the load to the full

ON position.

Light bulbs are burned out or not installed

• Replace or install light bulbs.

Dioded light bulbs

• Replace with non-dioded light bulbs.

Load does not

turn ON, and

LEDs on the

Plug-In Module

are OFF

Circuit breaker is OFF or tripped

• Turn circuit breaker ON.

Cord is not plugged in

•

Plug cord into wall outlet as shown in Installation.

Load turns

ON and OFF

continuously

Load is less than minimum load requirement

• Make sure the connected load meets the

appropriate minimum load requirement. See

Load Specifications.

Dimming

Module does

not dim

properly

Lamp has an integral dimmer

• Use lamp without an integral dimmer.

3-way switch on lamp is not set to full ON

• Turn 3-way switch on lamp to full ON

Plug-In Module

is warm

Solid-state control dissipation

• Plug-In Modules dissipate a small percentage

of the total connected load. It is normal for

the Plug-In Module to feel warm to the touch

during operation.

Appliance

Module

automatically

turns off

Over temperature condition

• Move Appliance Module to a cooler location

and / or reduce the load, then unplug and plug

the Appliance Module into the wall outlet.

Plug-In Module

doesn’t

respond to

a keypad,

wireless

controller, or

sensor

Improper programming

• Program according to the system Setup Guide.

Out of RF range

• Reposition to be within 30 ft (9 m) of an RF

signal repeater.

Already at current level

• The Plug-In Module has already responded to a

command, or is already at the requested setting.

Wireless controller or sensor batteries low or

installed incorrectly

• Replace or install batteries properly.

RF inteference

• Do not run Plug-In Module cords with other

power cords or communication wires (i.e.

networking, audio, or video signals).

Note: Refer to the system Setup Guide for additional troubleshooting

suggestions.

Returning a Plug-In Module to Factory Settings

Note: Returning a Plug-In Module to its factory settings will remove it

from the system and erase all programming.

Note: Unplug all switched loads from the Plug-In Module prior to

returning to factory settings.

Step 1 : Triple tap the toggle button on the Plug-In Module. DO NOT

release after the third tap.

Step 2 : Keep the toggle button pressed on the third tap (for

approximately 3 seconds) until the LED(s) on the

Plug-In Module scroll up and down or flash quickly.

Step 3 : Release the toggle button and immediately triple tap it again.

The LED(s) on the Plug-In Module will scroll up and down or

flash slowly.

The Plug-In Module has now been returned to factory settings and needs

to be reprogrammed into a system.

Warranty:

For warranty information, please see the enclosed Warranty, or visit

www.lutron.com/resiinfo

NOTE: Advanced Programming of a Plug-In Module requires

access to the module. Do this BEFORE installing if the module

will be hard to reach once installed. No load is required. You

may use any wall outlet within RF range.

†

Some low wattage loads may try to start when the Appliance Module is OFF due to 0.5 mA leakage

current through the module, similar to a night lighted toggle switch. Consult the load manufacturer for

compatibility.

††

Peak horsepower is not reflective of the UL® appliance horsepower rating. Consult appliance

manufacturer for UL horsepower rating.

Load Cord

Wall Outlet

1 2 3 4

Summary of Contents

Page 1 - POLARIZED cord set. It

RF Plug-In Modules Dimming Module : CCD-3PD-1Appliance Module: CCD-15APS-1120 V 50 / 60 HzTypical Power Consumption*: 0.3 WInstallation InstructionsP

Page 2 - Instrucciones de instalación

Módulos de enchufe de RFAtenuador: CCD-3PD-1Interruptor: CCD-15APS-1120 V 50 / 60 HzConsumo típico de potencia*: 0,3 WInstrucciones de instalaciónPo

Page 3 - POLARISÉ. Il

Modules RF enfichablesModule gradateur : CCD-3PD-1Module pour appareils électriques : CCD-15APS-1120 V 50 / 60 HzConsommation de puissance typique* :

Page 4 - Leia antes de instalar

Módulos Plug-in RF Módulo de dimerização: CCD-3PD-1Módulo do dispositivo: CCD-15APS-1120 V 50 / 60 HzConsumo normal de energia*: 0,3 WInstruções de i

Comments to this Manuals

No comments

AMX CCD-15APS-1 Setup Guide Page 1

Browse online or download Setup Guide for Dimmers AMX CCD-15APS-1. AMX CCD-15APS-1 User Manual

Summary of Contents

Comments to this Manuals

AMX CCD-15APS-1 Setup Guide Page 1

Browse online or download Setup Guide for Dimmers AMX CCD-15APS-1. AMX CCD-15APS-1 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Dimmers AMX CCD-15APS-1