AMX AVS-MD-3232-847 Instruction Manual Page 73
- Page / 191
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
RGBHV/HD-15 Boards
67
Modula Instruction Manual
Attaching Cables
Important: If using RGBHV/HD-15 boards in a CatPro system – first see “RGBHV+Stereo to CatPro
Boards with TXs and RXs” starting on page 69 for special system information.
When attaching RGBHV/HD-15 input and output cables, refer to the sheet labeled “AutoPatch Modula
Connector Guide” that ships with the system. The sheet shows you where to attach each cable on the rear
of each enclosure. Follow the sheet exactly; the system was programmed at the factory to operate only as
indicated on the sheet. For multiple-enclosure systems, each enclosure will be numbered (e.g., “Chassis
1 of 3”) on a label located on the left side (near the power receptacle).
To connect RGBHV/HD-15 inputs and outputs:
1.
Fasten the cables onto the input and output HD-15 connectors (FIG. 34).
HD-15 Board Connector Pinout
For High Density DB-15 board connector pinout information, see FIG. 35.
FIG. 34 Fasten cable onto input or output HD-15 connector
FIG. 35 RGBHV/HD-15 input and output board connector pinout
Note: 55 mA supplied on output pin 9; power draw not to exceed 50 mA per port.
RGBHV/HD-15 Board Connector Pinouts
Input (VESA DDC Compliant)
1. Red 6. Red GND 11. ID Bit
2. Green 7. Green GND 12. DDC SDA
3. Blue 8. Blue GND 13. Horizontal sync
4. ID Bit 9. +5 V in DDC 14. Vertical sync
5. GND 10. GND 15. DDC SCL
Output
1. Red 6. Red GND 11. ID Bit
2. Green 7. Green GND 12. ID Bit
3. Blue 8. Blue GND 13. Horizontal sync
4. ID Bit 9. +5 V out DDC 14. Vertical sync
5. GND 10. GND 15. ID Bit
- Instruction Manual 1
- Distribution Matrix 1
- Contents 3
- ESD Warning 7
- Copyright Notice 10
- Liability Notice 10
- USFCC Notice 10
- Lithium Batteries Notice 11
- Trademark Notices 11
- Warnings and Cautions 11
- Product Notes 13
- Modula Control Features 14
- Front View 15
- Rear View 16
- CPU/Control Board 17
- System Serial Number 18
- Expansion Slots 19
- Input and Output Connectors 19
- Modula Specifications 20
- Enclosure Configurations 23
- Applicability 24
- Input and Output Boards 25
- Expansion Board 25
- Installation and Setup 27
- Unpacking 28
- Installation Procedure 29
- FIG. 9 Attach rack ears 30
- Linking Enclosures 31
- Link Cables and Equipment 32
- Modula linked to Modula 33
- Control Options 37
- Attaching Serial Controllers 38
- FIG. 17 RS-422 pin diagram 39
- Signal Types and Connectors 43
- Applying Power and Startup 44
- Serial Control Device Startup 46
- Executing a Test Switch 47
- Troubleshooting 48
- Technical Support 49
- Standard Video Boards 51
- Wideband Boards 57
- HV Sync Video Boards 61
- HV Sync Boards Specifications 63
- S-Video Boards 65
- S-Video Boards Specifications 67
- RGBHV/HD-15 Boards 71
- RGBHV/HD-15 Specifications 72
- Modules 77
- Pinout for HD-15 connector 82
- CatPro System Equipment 83
- Routing Path A 85
- Routing Path B 85
- Routing Path C 86
- Adjustment Methods 87
- CatPro RX Module 88
- 13. Press the Adjust knob 91
- FIG. 51 Routing Path B 92
- Test image adjusted for skew 94
- Select the sources 94
- The Temporary RX Module Unit 95
- Stereo Audio Boards 99
- Applicability Table 2 100
- Specifications Table 1 101
- Stereo Applicability Table 4 101
- Specifications Table 2 102
- Specifications Table 3 103
- Specifications Table 4 104
- Attaching Wires 105
- Adjusting Output Volume 106
- Adjusting Input Gain 107
- Potentiometer Input Boards 108
- Mono Audio Boards 109
- Applicability Table 1B 110
- Applicability Table 1C 110
- Applicability Table 3 111
- (see page 105) 113
- Modula Instruction Manual 118
- Applicability Notice 119
- Compression Ratio 120
- Board Settings 123
- Attaching Cables 127
- Video Specifications 131
- Audio Specifications 132
- General Specifications 132
- System Setup 134
- Adjusting for Cable Length 135
- Module 137
- Attaching Cables and Wires 139
- RS-422 Boards 143
- Overview and System Setup 144
- RS-232 RS-422 146
- Port Configuration 147
- Termination Jumper 148
- Configuration and Control 149
- X to Y Fanout 150
- RS-422 Configuration Files 152
- Overview 153
- Installing XNConnect 154
- Opening a Configuration File 155
- Discovering a System 156
- Navigating the Interface 157
- Multiple Signal Paths 158
- Loading a Configuration File 162
- Modifying Virtual Matrices 163
- Joining Virtual Matrices 164
- Creating a New Virtual Matrix 167
- Under Channel Type: 169
- Grouping Pattern Examples 171
- Sequential Grouping Pattern 172
- Cabling Parallel Inputs 173
- Controlling Paralleled Inputs 175
- Adding Modula Boards 179
- Cabling the VIS board 187
- Serial Port Settings 188
- Vertical Interval Sync 190
- Increase Your Revenue 191
Related products and manuals for Video switches AMX AVS-MD-3232-847
Video switches AMX Optima SD Instruction Manual
(165 pages)
(165 pages)
Video switches AMX DXLink Instruction Manual
(148 pages)
(148 pages)
© 2020, manymanuals.com. All rights reserved. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals