AMX AVS-MD-3232-847 Instruction Manual Page 189
- Page / 191
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Appendix E – Vertical Interval Sync (VIS)
183
Modula Instruction Manual
4. Check the splash screen* to be sure the VIS board has been detected and is enabled (FIG. 121).
* Your splash screen may differ. AMX reserves the right to change the contents and/or formatting of the splash
screen without notice.
If the sync board is not detected and enabled:
(If the splash screen either reports a failure or does not report on the sync board:)
Power the system down.
Ensure the board is aligned with the board guides and is firmly in place.
Check that the source of the master sync signal is providing a good signal.
Re-enter ~scr! into HyperTerminal. Check the splash screen to see if the sync board is
detected. If it is still not detected, contact technical support (see page 43).
Enabling the VIS Board
To complete the installation, the VIS board must be enabled using one of the following two methods.
If the original configuration file has not been modified, use XNConnect to load the new file
that shipped with the board (see “Loading a Configuration File” on page 156). The new file
automatically enables the VIS board for the system.
If the original configuration file has been modified (local presets, names, etc.) and you do not
want to replace it follow the steps below.
Note: We recommend keeping a copy of the former configuration file for reference.
When loading any part of a configuration file, the matrix switcher must not be actively switching. You
may want to disconnect any external controllers to ensure that no switches are executed during the
loading of the file.
To enable a VIS board using XNConnect:
1.
Install XNConnect from the AMX AutoPatch CD sent with the new board. (If XNConnect is already
installed on the PC, we strongly recommend uninstalling the old version before installing a new
version).
2. Open XNConnect.
3. Using the standard File Open dialog box, locate and open your XCL (*.xcl) configuration file that
was sent with the new board. The default location is in the C:\AutoPatch\Configuration
Software<Version>\MyXCL folder.
FIG. 121 VIS recognition display in splash screen
AutoPatch Modula signal router
Host software: v3.1.0
.....
.....
I/O slots: xxxxxxxxxxxxxxxxxxxxxxxx
Sync board detected: checking for sync
signal...ok. Sync switching enabled.
Interface 1: BCS mode RS232 port, 9600 (8/1/N
)
VIS board detected
Text will vary depending
on the boards in the system
- Instruction Manual 1
- Distribution Matrix 1
- Contents 3
- ESD Warning 7
- Copyright Notice 10
- Liability Notice 10
- USFCC Notice 10
- Lithium Batteries Notice 11
- Trademark Notices 11
- Warnings and Cautions 11
- Product Notes 13
- Modula Control Features 14
- Front View 15
- Rear View 16
- CPU/Control Board 17
- System Serial Number 18
- Expansion Slots 19
- Input and Output Connectors 19
- Modula Specifications 20
- Enclosure Configurations 23
- Applicability 24
- Input and Output Boards 25
- Expansion Board 25
- Installation and Setup 27
- Unpacking 28
- Installation Procedure 29
- FIG. 9 Attach rack ears 30
- Linking Enclosures 31
- Link Cables and Equipment 32
- Modula linked to Modula 33
- Control Options 37
- Attaching Serial Controllers 38
- FIG. 17 RS-422 pin diagram 39
- Signal Types and Connectors 43
- Applying Power and Startup 44
- Serial Control Device Startup 46
- Executing a Test Switch 47
- Troubleshooting 48
- Technical Support 49
- Standard Video Boards 51
- Wideband Boards 57
- HV Sync Video Boards 61
- HV Sync Boards Specifications 63
- S-Video Boards 65
- S-Video Boards Specifications 67
- RGBHV/HD-15 Boards 71
- RGBHV/HD-15 Specifications 72
- Modules 77
- Pinout for HD-15 connector 82
- CatPro System Equipment 83
- Routing Path A 85
- Routing Path B 85
- Routing Path C 86
- Adjustment Methods 87
- CatPro RX Module 88
- 13. Press the Adjust knob 91
- FIG. 51 Routing Path B 92
- Test image adjusted for skew 94
- Select the sources 94
- The Temporary RX Module Unit 95
- Stereo Audio Boards 99
- Applicability Table 2 100
- Specifications Table 1 101
- Stereo Applicability Table 4 101
- Specifications Table 2 102
- Specifications Table 3 103
- Specifications Table 4 104
- Attaching Wires 105
- Adjusting Output Volume 106
- Adjusting Input Gain 107
- Potentiometer Input Boards 108
- Mono Audio Boards 109
- Applicability Table 1B 110
- Applicability Table 1C 110
- Applicability Table 3 111
- (see page 105) 113
- Modula Instruction Manual 118
- Applicability Notice 119
- Compression Ratio 120
- Board Settings 123
- Attaching Cables 127
- Video Specifications 131
- Audio Specifications 132
- General Specifications 132
- System Setup 134
- Adjusting for Cable Length 135
- Module 137
- Attaching Cables and Wires 139
- RS-422 Boards 143
- Overview and System Setup 144
- RS-232 RS-422 146
- Port Configuration 147
- Termination Jumper 148
- Configuration and Control 149
- X to Y Fanout 150
- RS-422 Configuration Files 152
- Overview 153
- Installing XNConnect 154
- Opening a Configuration File 155
- Discovering a System 156
- Navigating the Interface 157
- Multiple Signal Paths 158
- Loading a Configuration File 162
- Modifying Virtual Matrices 163
- Joining Virtual Matrices 164
- Creating a New Virtual Matrix 167
- Under Channel Type: 169
- Grouping Pattern Examples 171
- Sequential Grouping Pattern 172
- Cabling Parallel Inputs 173
- Controlling Paralleled Inputs 175
- Adding Modula Boards 179
- Cabling the VIS board 187
- Serial Port Settings 188
- Vertical Interval Sync 190
- Increase Your Revenue 191
Related products and manuals for Video switches AMX AVS-MD-3232-847
Video switches AMX Optima SD Instruction Manual
(165 pages)
(165 pages)
Video switches AMX DXLink Instruction Manual
(148 pages)
(148 pages)
© 2020, manymanuals.com. All rights reserved. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals