Amx Mio R-3 User Manual download pdf (Page 2)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

5/11

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-0148-03 REV: D

2. Holding the device in both hands, place your thumbs on the battery door

and slide the battery door free. The battery door should slide toward the

bottom end of the device.

3. Connect the terminal end of the Lithium-Ion battery to the port as shown

in FIG. 3. It may be necessary to use a thin, blunt non-conductive object

to seat the battery connector fully within its port.

Battery Low Indicator

When the battery charge level is too low to sustain continuous operation, the

LCD flashes "Battery Low" and the device shuts down.

Setup Mode

The Setup mode allows you to set the following device features.

Entering

Setup

mode

1. Press and hold the STOP button and the INPUT button. The two buttons

must be pressed within 0.1 seconds of each other and held down for 2

seconds. The device indicates you are now in Setup mode. See below for

available modes.

2. Press the EXIT key when you are finished.

Note: Your settings will not be lost in the event of battery removal or failure.

Transmit Mode

Press button 1 to select from one of the different available transmit modes. The

transmit mode changes each time 1 is pressed. The predetermined modes are

IR 38 Khz, IR 455 Khz, ZigBee Mode, IR 38 + Zig, and IR 455 + Zig. The

display indicates the selected mode.

Timeout Adjustment

Press button 2 on the remote to change the sleep timeout from the default.

Each time 2 is pressed, the sleep timeout raises incrementally. The pre-

determined sleep timeouts are 3, 6, 9, and 12 seconds. The display indicates

the selected sleep timeout.

Download Mode

In order to download new firmware or a new configuration or font file to the MIO

R-3 remote using the remote's program port, the remote must first be placed

into Download mode. Press 3 on the remote to toggle the Download mode OFF

and ON. The Download mode must be ON before you can download a file to

the MIO R-3. While the Download mode is ON, the device will not go to sleep.

Once the download is complete, this setting must be returned to Download Off.

A firmware download will cause the remote to reset and this will automatically

reset the remote to Download Off.

Debug Mode

Pressing button 4 on the remote toggles Debug mode between ON and OFF.

Pressing the button toggles to the new mode; 2 seconds after selecting the

mode, the menu returns to Setup mode. The remote will remain in the last

mode selected until Setup mode is once again entered and this mode is

changed by pressing the 4 button.

Firmware Version

Pressing button 5 on the remote displays the remote and ZigBee firmware

versions currently loaded on the remote. To view the available firmware

versions, press the Move Up arrow on the scroll wheel to scroll up. and

pressing the Move Down arrow will scroll down. When finished, press Exit to

save the changed firmware information and leave Setup mode.

Device ID

Pressing button 6 displays the device’s Device ID number. To change the

Device ID number, press the Move Up arrow on the scroll wheel to scroll up.

and pressing the Move Down arrow will scroll down. To move the cursor to the

next number, use the Move Left or Move Right arrows on the scroll wheel to

change positions.

After all numbers have been configured as desired, pressing the center button

on the scroll wheel will store the entered Device ID into memory. After the

Device ID is stored into memory, the display will return to Setup mode.

LED Awake Brightness

Pressing button 7 on the remote toggles the Power LED Brightness mode from

LOW to MED and then HIGH. The display indicates the selected mode.

LED Sleep Mode Brightness

Pressing button 8 on the remote toggles the Sleep Brightness mode from OFF

to LOW and then MED. The Sleep brightness is the state the MIO R-3 assumes

while in the charging cradle.

ZigBee ID PAN, Channel and System Connection

Pressing the 9 button will display the current Extended ZigBee Personal Area

Network (PAN) ID and channel for the device. In order to display the NetLinx

Master IP and ZigBee gateway EUI addresses, press the Move Up arrow on

the scroll wheel to scroll up. and pressing the Move Down arrow will scroll

down. When finished, press Exit to save the Extended PAN ID and channel

information and leave Setup mode.

Site Survey

Pressing the 0 button makes the MIO R-3 scan all frequencies and store all

joinable Extended PAN IDs and Channels in memory. The display will show the

first accessible Extended PAN ID and Channel.

To display other Extended PAN IDs and Channels found in the area, press the

Move Up or Move Down arrows on the scroll wheel until the remote displays

the desired Extended PAN ID and Channel.

To connect to a particular Extended PAN ID, pressing the center button on the

scroll wheel will initiate the remote to connect to a network. If no networks were

found, the display will read SCAN FAIL before returning to Setup mode.

Programming The MIO R-3 Using KeypadBuilder

Most functionality of the MIO R-3 is handled using the KeypadBuilder

application. Go to www.amx.com for the supporting documentation.

The MIO R-3 recognizes a select number of Serial Commands and

SEND_COMMANDs. For a full list and descriptions, consult the Programming

section of the MIO R-3 instruction manual at www.amx.com.

Using the Programming Jack on The MIO R-3

The programming jack (see FIG. 2) is used for communication between the

device and KeypadBuilder. The programming jack uses a three-wire, 2.5mm

stereo jack, and you can order the programming cable (FG10-817) from AMX if

you do not currently possess one.

To download KeypadBuilder Configuration Files:

1. Set the MIO R-3 Download mode to ON.

2. Flip and turn the device so that the buttons are facing away from you and

the device is upside down.

3. Holding the device in both hands, place your thumbs on the battery door

and slide the battery door free. The battery door will slide in the direction

of the bottom end of the device.

4. Connect the 2.5mm stereo plug (male) end of the programming cable

(FG10-817) into the programming jack on the bottom side of the remote

device.

5. If necessary, connect the DB-9 end of the programming cable to the

female DB-9 connector on the DB-9 extension cable (FG10-727).

6. Connect the female DB-9 terminal end of the extension cable to the port

on the back of your computer.

7. Configure the communication parameters in KeypadBuilder.

Patents

This product is covered by the following patents:

AMX

U.S. Patent No. D 602,858

U.S. Patent No. D 520,495

U.S. Patent No. 7,786,623

This product employs or practices certain features and/or methods of one or

more of the following patents:

SIPCO, LLC

U.S. Patent No. 7,103,511

U.S. Patent No. 6,914,893

U.S. Patent No. 7,697,492

FIG. 3 Rechargeable Battery Port on The MIO R-3 Remote

Lithium-Ion Battery

Rechargeable

Battery

Port Connection

Correct path for

battery wires and

connector

1 2

Comments to this Manuals

No comments

Amx Mio R-3 User Manual Page 2

Comments to this Manuals

Related products and manuals for Remote control Amx Mio R-3