Amx Mio R-1 User Manual download pdf (Page 2)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

4/07

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-0147 REV: C

Using Connector Ports on The Mio R-1

The programming jack is used for communication between the device and

KeypadBuilder. The programming jack uses a three-wire, 2.5 mm stereo jack, you

can order the programming cable (FG10-817) from AMX if you do not currently

possess one. While loading your configuration file make sure the device is situated

as such that the batteries will not fall out. The load will fail if your batteries fall out

during the process. The Mio communicates at 115200 baud rate.

To download KeypadBuilder Configuration Files:

1. Set the Mio R-1 Download mode to ON. See the Configuration Mode section

for details.

2. Flip and turn the Mio R-1 device so that the buttons are facing away from you

and the device is upside down.

3. Holding the device in both hands, place your thumbs on the battery door and

slide the battery door free.

4. Connect the 2.5 mm stereo plug (male) end of the programming cable (FG10-

817) into the programming jack on the bottom side of the remote device.

5. If necessary, connect the DB-9 end of the programming cable to the female

DB-9 connector on the DB-9 extension cable (FG10-727).

6. Connect the female DB-9 terminal end of the extension cable to the port on the

back of your computer.

7. Configure the communication parameters in KeypadBuilder.

IR Code Matrix

The IR Code emitted depends upon which of the 6 configurable modes is selected.

Below is the list of codes for each button within each mode.

Configuration Mode

The configuration mode allows you to set the following device features:

• IR Transmit Mode (38 KHz or 455 KHz)

• Timeout Adjustment

• Download Mode

• Debug Mode

• Battery Type

• LED Awake Brightness

• LED Sleep Brightness

To enter configuration Mode:

1. Press and hold the STOP button and the INPUT button. The two buttons must

be pressed within 0.1 seconds of each other and held down for 2 seconds. The

device indicates you are now in configuration mode. See below for available

modes.

2. Press the EXIT key when you are finished.

Note: Your settings will not be lost in the event your batteries die or are removed.

IR Transmit Mode

Pressing button "1" on the remote toggles the IR transmission mode between 38KHz

and 455KHz. The display indicates the current mode.

Timeout Adjustment

Press button "2" on the remote to change the sleep timeout from the default. Each

time "2" is pressed, the sleep timeout raises incrementally. The

pre-determined sleep timeouts are:

• 3 seconds

• 6 seconds

• 9 seconds

• 12 seconds

The display indicates the selected sleep timeout.

Download Mode

Pressing "3" on the remote toggles the Download mode OFF and ON. The Download

mode must be ON before you can download a file to the Mio R-1 device. While the

Download mode is ON the device will not go to sleep. A power cycle will return the

device to Download OFF.

Debug Mode

Pressing button "4" on the remote toggles development mode between ON and OFF.

The display indicates the selected mode. In development mode, the display shows

the IR code assigned to buttons when pressed.

This mode is useful to the programmer when determining what IR codes are

associated to each mode.

Battery Type

Pressing button "6" on the remote toggles the battery type between Normal and

Recharge. The display indicates the selected type. The type of battery in the Mio R-1

dictates the battery type you need to set.

LED Awake Brightness

Pressing button "7" on the remote toggles the Power LED brightness mode from

LOW to MED and then HIGH. The display indicates the selected mode.

LED Sleep Mode Brightness

Pressing button "8" on the remote toggles the Sleep brightness mode from OFF to

LOW and then MED. The Sleep brightness is the state the Mio R-1 assumes while in

the charging cradle.

FIG. 3

Connecting The Keypad Device to Your PC

IR Code Matrix

Button Label Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6

1 Power Symbol 9 49 89 129 169 209

2 GUIDE 38 78 118 158 198 238

3 EXIT 37 77 117 157 197 237

4 MENU 31 71 111 151 191 231

5 INFO 39 79 119 159 199 239

6 L 32 72 112 152 192 232

7 M 33 73 113 153 193 233

8 K 34 74 114 154 194 234

9 A 35 75 115 155 195 235

10 SELECT 36 76 116 156 196 236

11 VOL + 24 64 104 144 184 224

12 VOL - 25 65 105 145 185 225

13 CH + 22 62 102 142 182 222

14 CH - 23 63 103 143 183 223

15 LAST 40 80 120 160 200 240

16 MUTE 26 66 106 146 186 226

17 1 11 51 91 131 171 211

18 2 12 52 92 132 172 212

19 3 13 53 93 133 173 213

20 4 14 54 94 134 174 214

21 5 15 55 95 135 175 215

22 6 16 56 96 136 176 216

23 7 17 57 97 137 177 217

24 8 18 58 98 138 178 218

25 9 19 59 99 139 179 219

26 INPUT 29 69 109 149 189 229

27 0 10 50 90 130 170 210

Stereo plug male

DB-9 connector

Cable FG10-817 to cable FG10-727

to PC

programming

cable

Keypad device

Programming

jack

Mio R-1

IR Code Matrix (Cont.)

Button Label Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6

28 ENTER 21 61 101 141 181 221

29 A (Macro 1) 250 250 250 250 250 250

30 B (Macro 2) 251 251 251 251 251 251

31 C (Macro 3) 252 252 252 252 252 252

32 TV (Mode 1) 241 241 241 241 241 241

33 SAT (Mode 2) 242 242 242 242 242 242

34 DVD (Mode 3) 243 243 243 243 243 243

35 CD (Mode 4) 244 244 244 244 244 244

36 AUX (Mode 5) 245 245 245 245 245 245

37 LGHT (Mode 6) 246 246 246 246 246 246

38 STOP B 2 42 82 122 162 202

39 REC J 8 48 88 128 168 208

40 PAUSE C 3 43 83 123 163 203

41 S. REV Z 7 47 87 127 167 207

42 PLAY A 1 41 81 121 161 201

43 S. FWD Y 6 46 86 126 166 206

44 REW E 5 45 85 125 165 205

45 FWD D 4 44 84 124 164 204

1 2

Comments to this Manuals

No comments

Amx Mio R-1 User Manual Page 2

Comments to this Manuals

Related products and manuals for Remote control Amx Mio R-1