AMX NI-700 User Manual download pdf (Page 2)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

060-004-2692 06/06

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-2105-03

REV: H

Connections and Wiring

FIG. 2 shows the layout of the connectors and components located on the rear

of the NI-700 NetLinx Integrated Controller.

Wiring a Power Connection

Use a 12 VDC-compliant power supply to provide power to the NI-700 through

the rear 2-pin 3.5 mm mini-Phoenix connector (FIG. 2). Use the previous power

requirements information to determine the power draw.

The incoming PWR and GND cable from the power supply must be connected

to their corresponding locations within the PWR connector. Refer to the NetLinx

Integrated Controllers Instruction Manual for more detailed wiring connection

information.

RS-232/422/485 Wiring Connector Information

FIG. 3 shows the pinout and wiring specification information for the rear

RS-232/RS-422/RS-485 (DB9) Device Ports. These ports support most

standard RS-232 communication protocols for data transmission (NI-700 uses

Ports 1 & 2).

Ethernet 10/100 Base-T Connector

A standard CAT5 Ethernet cable provides 10/100 network connectivity between

the Integrated Controller and the network (FIG. 4).

Note: On NetLinx Masters (such as those aboard the NI-700), from within the

Telnet or Terminal applications; you can send the SET ETHERNET MODE

command to assign the speed of your Ethernet connection.

Sample NI-700 command:

SET ETHERNET MODE AUTO

The NI-700 only allows you to set the Ethernet mode to AUTO negotiate

the Ethernet connection speed. Using any of the other connection modes

(10 Half/Full or 100 Half/Full) results in an error message.

Program Port Baud Rate Settings

The Configuration DIP switch is located on the front panel. Use this DIP switch

to set the baud rate for the Program Port, according to the settings shown in the

following table. Make sure the baud rate you set matches the baud rate on your

PC's NetLinx COM Settings before programming the unit.

By default, the baud rate is set to 38,400 (bps).

Note: DIP switch 1 activates/deactivates the Program Run Disable Mode. DIP

Switches 2,3, and 4 must remain OFF at all times.

Setting the Configuration (Program Port) DIP Switch

1. Disconnect the power supply from the rear 2-pin PWR (green) connector.

2. Set DIP switch positions according to the information listed in the previous

Baud Rate Settings table.

3. Reapply power to the unit.

Preparing the NI-700 for Serial Communication

1. Launch NetLinx Studio 2.x (default location is Start > Programs > AMX

Control Disc > NetLinx Studio 2 > NetLinx Studio 2).

2. Select Settings > Master Communication Settings, from the Main

menu, to open the Master Communication Settings dialog box.

3. Click the Communications Settings button to open the Communications

Settings dialog.

4. Click the NetLinx Master radio button (from the Platform Selection

section) to indicate you are working with a NetLinx Master.

5. Click the Serial radio button (from the Transport Connection Option

section) to indicate you are connecting to the Master via a COM port.

6. Click the Edit Settings button (on the Communications Settings

dialog) to open the Serial Settings dialog and set the COM port

parameters (used to communicate to the NetLinx Master).

7. Click the OK button three times to return to the main application.

8. Right-click the entry in the Online Tree tab and select Refresh System.

9. Assign a System Value by using Diagnostics > Device Addressing from

the Main menu.

10. Enable the Change System selection by clicking on it and then enter the

current and new System values.

11. Click the Change Device/System Number button and when finished

click Done.

12. Select To ols > Reboot the Master Controller to access the Reboot the

Master dialog, then click Reboot to restart the Master and incorporate

any changes.

13. Once the dialog replies with "Reboot of system complete", click Done and

then click the OnLine Tree tab in the Workspace window to view the

devices on the System.The default System value is one.

14. Right-click on the Empty Device Tree/System entry and select Refresh

System to re-populate the list.

Configuring the NI-700 for Ethernet Communication

Before continuing, complete the COM port steps above.

1. Connect an Ethernet cable to the unit’s rear Ethernet connector.

2. Select Diagnostics > Network Address from the Main menu and enter

the System, Device (0 for a Master), and Host Name information.

3. To configure the Address:

• Use a DHCP Address by selecting the Use DHCP radio button, then click

the GET IP button (to obtain a DHCP Address from the DHCP Server),

click the SET IP Information button (to retain the new address), and then

finish the process by clicking the Reboot Master > OK buttons.

• Use a Static IP Address by selecting the Specify IP Address radio

button, enter the IP parameters into the available fields, then click the

SET IP Information button (to retain the pre-reserved IP Address to the

Master), and then click the Reboot Master > OK buttons to finish the

process.

4. Repeat steps 1 - 5 from the previous section but rather than selecting the

Serial option, choose TCP/IP and edit the settings to match the IP

Address you are using (whether Static or IP).

5. Click on the Authentication Required radio box (if the Master is

secured) and press the User Name and Password button to enter a

valid username and password being used by the secured Master.

6. Click the OK button three times to return to the main application.

FIG. 2 NI-700 rear connectors and components

FIG. 3 RS-232/422/485 DB9 (male) connector pinouts

FIG. 4 Layout of Ethernet LEDs

IR RX

GND

I/O

PWR

4 23 1

AXlink

GND

AXP

AXM

PWR

12VDC

PORT 2 PORT 1

ETHERNET

SPDL/A

10/100

GND

IR IN

AUX

+12V

AXLink LED

IR RX

RS-232/422/485 (Ports 1 & 2)

I/O (Port 4)

IR/Serial

Rear

(green)

(Port 5)

Ethernet

AXLink

port

PWR

(Port 3)

Male

DB9 Serial Port pinouts (male connector)

Pin 2: RX signal

Pin 3: TX signal

Pin 5: GND

Pin 7: RTS

Pin 8: CTS

RS-232

Pin 1: RX -

Pin 4: TX +

Pin 5: GND

Pin 6: RX +

Pin 9: TX -

RS-422

Pin 1: A (strap to 9)

Pin 4: B (strap to 6)

Pin 5: GND

Pin 6: B (strap to 4)

Pin 9: A (strap to 1)

RS-485

10/100

ETHERNET

SPDL/A

SPD - Speed LED lights (yellow) when

and turns Off when the speed

is 10 Mbps.

the connection speed is 100 Mbps

L/A - Link/Activity LED lights

(green) when the Ethernet

cables are connected and

terminated correctly.

Baud Rate Settings

Baud Rate Position 5 Position 6 Position 7 Position 8

9600 bps OFF ON OFF ON

38,400 bps

(default)

OFF ON ON ON

57,600 bps ON OFF OFF OFF

115,200 bps ON ON ON ON

1 2

Comments to this Manuals

No comments

AMX NI-700 User Manual Page 2

Comments to this Manuals

Related products and manuals for Networking AMX NI-700