AMX NI-700 User Manual download pdf

Quick Start Guide

NI-700 NetLinx Integrated Controller

For more detailed installation, configuration, programming, file transfer, and

operating instructions, refer to the NI-700 and NI-900 NetLinx Integrated

Controllers Instruction Manual, available on-line at www.amx.com.

Overview

The NI-700 unit (FG2105-03) is geared to meet the specific control and

automation needs of a single room environment, where both price and

functionality are the driving requirement. This product is configured to control a

limited number of video players, projectors, lighting, thermostats, and other

electronic equipment. The NI-700 provides support for 1 IR/Serial Output port,

2 RS-232/RS-422/RS-485 ports, 4 Digital Input/Output ports, and 1 IR RX port.

ATTENTION!

Verify you are using the latest version of NetLinx Studio (available for

download from www.amx.com).

Port Assignment and Functionality

Ethernet Ports used by the NI Controller

Note: While the NI-700 is capable of receiving 8 and 9 bit characters, it cannot

receive 7 bit, 1 stop bit data from a serial device (ex: 9600,N,7,1).

FIG. 1 NI-700 NetLinx Integrated Controller (front view)

NI-700 Specifications

Dimensions

(HWD):

• 1.58" x 5.54" x 5.12" (4.01 cm x 14.10 cm x 13.00 cm)

• 1 rack unit high

Power

Requirement:

• 280 mA @ 12 VDC

• Power requirements are usage dependant

Memory: • 32 MB SDRAM (not upgradeable)

• 16 MB Flash chip (not upgradeable)

• 512 Kb of Non-volatile SRAM

• Refer to the NI-700 and NI-900 NetLinx Integrated Controllers

Instruction Manual for more information.

Microprocessor: • 304 MIPS

Weight: • 1.30 lbs (0.59 kg)

Enclosure: • Metal with black matte finish

Certifications: • FCC Part 15 Class B, CE, and IEC 60950

Front Panel

Components:

• Program Port: RS-232 DB9 connector (male) can be connected to

a DB9 port on a PC. This port can be used with both Serial and

NetLinx commands.

• Configuration DIP Switch: Sets the communication parameters for

the Program port.

• IR RX LED: Red LED lights when IR data is being received via the

rear IR RX port.

• IR LED: Red LED lights during the transmission of IR or Serial

data via the rear IR port.

• I/O LEDs: Four yellow LEDs light when the rear I/O channels 1 - 4

are active. LED indicator for each I/O port reflects the state of that

particular port.

• Serial LEDs: Two sets of red and yellow LEDs light when the rear

DB9 Ports (1 & 2) transmit or receive RS-232, 422, or 485 data.

These LEDs do not reflect changes in either the RTS or CTS

when hardware handshaking is used.

• LINK/ACT: Green LED lights when the Ethernet cable is

connected and an active link is established. This LED also blinks

when receiving Ethernet data packets.

• Status: Green LED lights when the Controller is programmed and

communicating properly.

• Output: Red LED lights when the Controller transmits data, sets

channels On and Off, sends data strings, etc.

• Input: Yellow LED lights when the Controller receives data from

button pushes, strings, commands, channel levels, etc.

• ID Pushbutton: Sets the NetLinx ID (Device only) assignment for

the device.

Rear Panel

Connectors:

• RS-232/422/485 (Ports 1 & 2): Two RS-232/422/485 control ports

use DB9 (male) connectors with XON/XOFF (transmit On/

transmit Off), CTS/RTS (clear to send/ready to send), and 300 -

115,200 baud.

• IR RX (Port 5): 4-pin 3.5 mm mini-Phoenix port is used to connect

one or more (8 maximum) IRX-SM+ swivel mount or IRX-DM+

Decora mount IR receivers.

The IR RX port functions using AMX IR codes (38 KHz and

455 KHz) and works ONLY with AMX IR Receivers such as the

IRX-DM+ and IRX-SM+.

• Digital I/O (Port 4): 4-channel binary I/O port for contact closure

with each input being capable of voltage sensing. Input format is

software selectable with interactive power sensing for IR ports.

NI-700 Specifications (Cont.)

Rear Panel

Connectors

(Cont.):

•IR/Serial (Port 3): 4-pin 3.5 mm mini-Phoenix port is capable of

supporting high-frequency carriers of up to 1.142 MHz with the

output being capable of three electrical formats: IR, Serial, Data.

IR ports support data mode (at limited baud rates and wiring

distances).

• AXlink LED: Green LED indicates the state of the AXlink port.

• AXlink Port: 4-pin 3.5 mm mini-Phoenix (male) connector provides

data and power to external control devices.

• Ethernet Port: RJ-45 port for 10/100 Mbps communication. LEDs

show communication activity, connection status, speeds, and

mode information:

SPD (speed) - Yellow LED lights On when the connection speed

is 100 Mbps and turns Off when the speed is 10 Mbps.

L/A (link/activity) - Green LED lights On when the Ethernet cables

are connected and terminated correctly, and blinks when

receiving Ethernet data packets.

• Power Port: 2-pin 3.5 mm mini-Phoenix (male) connector

Operating

Environment:

• Operating Temperature: 0° C (32° F) to 50° C (122° F)

• Operating Humidity: 20% - 85% RH

Included

Accessories:

• 2-pin 3.5 mm mini-Phoenix female PWR connector (41-5025)

• 4-pin 3.5 mm mini-Phoenix female connector (41-5047)

• 6-pin 3.5 mm mini-Phoenix female I/O connector (41-5063)

• CC-NIRC IR Emitter

• NI-700 Quick Start Guide

Other AMX

Equipment:

• AC-RK Accessory Rack Kit (FG515)

• CC-NIRC IR cables (FG10-000-11)

• CC-NSER IR/Serial cables (FG10-007-10)

• CSB Cable Support Bracket (FG517)

• IRX-DM+ IR Sensor (FG458-10 and FG458-11)

• IRX-SM+ IR Sensor (FG455-01)

• PMB Pole Mount Bracket (FG531)

• STS, Serial To Screw Terminal (FG959)

• Surface Mount Bracket Accessory (FG525)

NI-700 Port Assignments

Port ICSP Port #

Serial Port #1 1

Serial Port #2 2

IR/Serial Port 3

I/O Port 4

IR RX Port 5

Ethernet Port Usage

Port type Description Standard Port #

FTP The on-board Master has a built-in FTP server. 21/20 (TCP)

SSH The SSH port functions using the same interface as

Telnet but over a secure shell where it uses SSL as a

mechanism to configure and diagnose a NetLinx

system.

Note: SSH version 2 is only supported.

22 (TCP)

Telnet The NetLinx Telnet server provides a mechanism to

configure and diagnose a NetLinx system.

23 (TCP)

HTTP The Master has a built-in web server that complies

with the HTTP 1.0 specification and supports all of the

required features of HTTP v1.1. This port is used for

unsecure HTTP Internet communication between the

web browser’s UI and the target Master.

80 (TCP)

HTTPS/SSL This port is used by a web browser to securely

communicate between the web server UI and the

target Master.

443 (TCP)

ICSP Peer-to-peer protocol used for both Master-to-Master

and Master-to-device communications.

1319 (UDP/TCP)

integration!

Solutions

This feature on the Master uses, by default, port

10500 for the XML based communication protocol.

This port is connected to by the client web browser’s

JVM when integration! Solutions control pages are

retrieved from the on-board Master’s web server.

10500 (TCP)

1 2

Summary of Contents

Page 1 - Quick Start Guide

Quick Start GuideNI-700 NetLinx Integrated ControllerFor more detailed installation, configuration, programming, file transfer, and operating instruct

Page 2 - Connections and Wiring

AMX NI-700 User Manual

Browse online or download User Manual for Networking AMX NI-700. NI-700 Quick Start Guide

Summary of Contents

More documents for Networking AMX NI-700

Comments to this Manuals

AMX NI-700 User Manual

Browse online or download User Manual for Networking AMX NI-700. NI-700 Quick Start Guide

Summary of Contents

More documents for Networking AMX NI-700

Comments to this Manuals

Related products and manuals for Networking AMX NI-700