AMX DXLink Instruction Manual Page 88
- Page / 148
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
NetLinx Programming – DXLink Fiber TXs/RXs
88
Instruction Manual – DXLink Fiber Transmitters and Receivers
IR SEND_COMMANDs (Transmitters and Receivers), continued
CH
Send IR pulses for the selected
channel.
• All channels below 100 are transmitted as two digits.
• If the IR code for ENTER (function #21) is loaded, an Enter will follow the
number.
• If the channel is greater than or equal to (>=) 100, then IR function 127 or 20
(whichever exists) is generated for the one hundred digit.
Note: Set the Pulse and Wait times with 'CTON' (see page 88) and 'CTOF'
(see page 88).
Syntax:
SEND_COMMAND <DEV>,"'CH',<channel number>"
Valid responses:
channel number = 0 to 199 channels
Example:
SEND_COMMAND IR_1,"'CH',18"
The IR port on the DXLink Fiber TX or RX performs the following:
• Transmits IR signals for 1 (IR code 11).
• The transmit time is set with the CTON command.
• Waits until the time set with the CTOF command elapses.
• Transmits IR signals for 8 (IR code 18).
• Waits for the time set with the CTOF command elapses.
If the IR code for Enter (IR code 21) is programmed, the unit performs the
following steps:
• Transmits IR signals for Enter (IR code 21).
• Waits for the time set with the CTOF command elapses.
CP
Halt and clear all active or buffered IR
commands, and then send a single IR
pulse.
Pulse and Wait times can be set with the 'CTON' and 'CTOF' commands.
Syntax:
SEND_COMMAND <DEV>,"'CP',<code>"
Valid responses:
code = IR port’s channel value 0 to 252 (253 to 255 reserved).
Example:
SEND_COMMAND IR_1,"'CP',2"
Clears the active/buffered commands and pulses IR port’s channel 2.
CTOF
Set the duration of the Off time (no
signal) between IR pulses for channel
and IR function transmissions. Off
time settings are stored in non-volatile
memory.
This command sets the delay time between pulses generated by the 'CH' or
'XCH' Send Commands in tenths of seconds.
Syntax:
SEND_COMMAND <DEV>,"'CTOF',<time>"
Valid responses:
time = 0 to 255. Given in 1/10th of a second increments. Default is 5
(0.5 seconds).
Example:
SEND_COMMAND IR_1,"'CTOF',10"
Sets the off time between each IR pulse to 1 second.
CTON
Set the total time of IR pulses
transmitted and is stored in
non-volatile memory.
This command sets the pulse length for each pulse generated by the 'CH' (see
page 88) or 'XCH' (see page 89) Send Commands in tenth of a second
increments.
Syntax:
SEND_COMMAND <DEV>,"'CTON',<time>"
Valid responses:
time = 0 to 255. Given in 1/10th of a second increments. Default is 5
(0.5 seconds).
Example:
SEND_COMMAND IR_1,"'CTON',20"
Sets the IR pulse duration to 2 seconds.
CH SEND_COMMAND
CTOF
SEND_COMMAND
CTON
SEND_COMMAND
- Instruction Manual 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Apache License, Version 2.0 10
- Warnings and Cautions 11
- Overview DXLink Fiber 12
- Bidirectional Mode 13
- Unidirectional Mode 13
- Data Link-lost Mode 13
- Product Notes 14
- Directive 15
- DXLink Fiber HDMI Receivers 16
- DXLink Fiber Boards 17
- Common Applications 18
- DXLink Fiber Transmitters 19
- DXLink Fiber Receivers 23
- Power Jack 24
- Common Features/Functionality 26
- HID Devices and Windows 8 27
- 4. Click OK 28
- DXLink Fiber Specifications 32
- qualified): 1 per unit 33
- Analog Video Specifications 36
- Local Audio Specifications 37
- Installation and Setup 38
- Setup Information 39
- Example 40
- Endpoint/ 40
- Bidirectional 40
- HDMI Out 41
- Fiber Out 41
- Fiber OutHDMI In 41
- Fiber In 41
- DIP Switch Location 44
- #2 Toggle Settings 45
- #3 Toggle Settings 45
- Setting DIP Switch #4 46
- Common Scenarios 46
- Table - Bidirectional 46
- Table - Unidirectional 47
- ICS LAN 10/100 LEDs 50
- Audio Type Precedence 51
- Local Area Network 57
- ID Pushbutton Functions 60
- To set the Scaling Mode: 61
- Bypass Mode 61
- Auto Mode 61
- Manual Mode 61
- Persistence of Scaling Mode 62
- Network Configuration 65
- TCP/IP Address Configuration 66
- External Master Versions 66
- Factory Default Parameters 67
- Device IDs 68
- Using the ID Pushbutton 68
- Factory Parameters* 70
- IRL File Transfers 72
- Transferring IRL Files 74
- Additional Documentation 76
- Additional IRL Information 76
- Device Numbering and Ports 77
- VIDOUT_RES_REF 79
- SEND_COMMAND 79
- VIDOUT_SCALE 79
- Scaling Modes 79
- VI<input>O 82
- <output> 82
- VIDIN_EDID 84
- IR CHANNELs 87
- IR SEND_COMMANDs 87
- AUDIN_FOR 87
- CH SEND_COMMAND 88
- XCH SEND_COMMAND 89
- USB SEND-COMMANDs (Receiver) 93
- PERSISTAV 95
- SEND_STRING Escape Sequences 96
- Troubleshooting 97
- DXLink Fiber Troubleshooting 98
- Network Setup Issues 99
- Technical Support 99
- Overview 100
- Important Upgrade Information 102
- Firmware Versions 102
- Transferring KIT Files 103
- Example: 104
- Telnet Username and Password 105
- Telnet Commands 106
- Telnet Commands (continued) 108
- Guidelines 119
- TCP vs. UDP 119
- URL vs. NDP vs. Auto 120
- Windows Client Programs 120
- Linux Telnet Client 120
- Creating a Virtual Master 123
- CONNECTION and press Enter 126
- HDMI Connector Cable Pinout 127
- HD-15 Connector Cable Pinout 128
- DVI Cable Connector Pinout 129
- CEA (RGB Color Space): 134
- CVR (RGB Color Space): 135
- CVT (RGB Color Space): 136
- DMR (RGB Color Space): 137
- DMT (RGB Color Space): 137
- Applicability Notice 138
- DXLink Fiber and EDID 141
- USER EDID 1 142
- USER_EDID_MODIFIED 142
- MIRROR OUT 1 142
- MIRROR_OUT_LOCAL 142
- AMX EDID Library 142
- Software Installation on PC 143
- DXLink Fiber Connection to PC 144
- EDID Programmer tab 144
- EDID Programmer View 145
- Read Error Message 146
- 11/19/14 148
Related products and manuals for Video switches AMX DXLink
(79 pages)© 2020, manymanuals.com. All rights reserved. | 1.420 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals