AMX APEX Destiny 6100 Specifications Page 16
- Page / 84
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
16
Two-Way Adjustment: The potentiometer marked "2-WAY VOL" controls the volume level of voice over the
phone line to the inside speaker during two-way communication or paging. Using a
small screwdriver, turn the potentiometer to obtain the desired volume. Clockwise
increases volume. This adjustment will not the affect alarm notification volume from the
speaker during an activation. Use of two-way voice is not evaluated for UL installation.
Upload / Download LED: At the top right of the board is a yellow LED labeled "U/D" which is illuminated when
there is a modem to modem connection during upload or download.
POWER LED: At the top right of the board is a red LED labeled "POWER" which is illuminated when
the system is receiving power.
STATUS LED: At the top right of the board is a green LED labeled "STATUS" which flashes to show the
microprocessor is functioning. An incoming ring detection will cause this LED to flash
very fast.
Dial LED: At the top right of the board is a red LED labeled "DIAL" which is illuminated during
digital communication and remote phone access. The Dial LED is used as a diagnostic
tool to analyze communication problems. The number of flashes after a failed attempt
correlates to the communication stage that caused the system to fail. See
"Communicator Diagnostics" for more information.
Phone LED: At the top right of the board is a green LED labeled "PHONE" which is illuminated when
the system's supervision of the phone line verifies a valid phone line on "R" and "T." If
the system does not confirm a phone line, the LED will turn off. Phone line failures can
be indicated at the keypad as well as sound a local alarm. Phone line restoration can be
communicated to the central station.
X-10 TW-523 Interface: Plug a standard RJ-12 cord into J5 on the middle right side of the board when using the X-
10 TW-523 (X-10 Pro PSC05) module for lighting options. The termination of the four
wire connection will be another RJ-12 jack plugged into the TW-523. The cord must
have four wires (see "X-10 interface Cord"). 2-wire cords will not work. Use of X-10 is
not UL listed for fire and burglary functions and is intended for hom automation. See
Control Channel section for programming information.
X-10 Interface Cord
A 4-conductor phone cord must be used to connect an X-10 TW-523 (X10-Pro PSC05) to the interface jack on the
control panel. Maximum cord length is 15 feet. The conductors must be in the following order:
YG R B B R G Y
- DESTINY 6100 1
- Software Revisions 4
- Table of Contents 5
- System Options and Times 6
- Central Station Features 6
- User Codes 7
- Control Channels 7
- Specifications 8
- Inserting the Cabinet Lock 11
- Mounting the Control Board 11
- To House 12
- From Phone 12
- Wiring Notes 13
- System Terminals 14
- X-10 Interface Cord 16
- Program Mode 18
- Locations and Values 18
- Automated Locations 18
- Exiting Program Mode 18
- Programming 18
- Quick Start 19
- System Input Overview 20
- Programming System Inputs 20
- System Setup Example 21
- Using This Manual: 22
- Program a Zone 23
- Zone Questions 23
- * Zone Type 24
- Zone Options 1 24
- Zone Options 2 24
- Hardware Device Types 25
- Predefined Zone Assignments 25
- Hardwire Inputs 26
- 5816 (MN) 5817 27
- Button Type Devices 28
- Button Functions 29
- Editing Zone Programming 30
- Deleting a Zone 30
- Smoke Verification 33
- Speaker (Bell) Supervision 34
- RF Jam Detection 34
- System Options - Group 1 36
- System Options - Group 2 36
- System Options - Group 3 36
- System Options - Group 4 37
- System Options - Group 5 37
- System Options - Group 6 37
- System Access Codes 37
- System Times 38
- Monitor Trouble Conditions 38
- Bypass Options 38
- Phone Access Options 39
- Event Memory Log 39
- Communicator Times 46
- Two-Way Voice Options 46
- Two-Way Digit Assignments 47
- Report Codes 49
- Dialer Options 51
- Communicator Diagnostics 51
- User Communicator Test 51
- Central Station Terms 52
- Key Function Values 56
- Keypad Option 56
- Keypad Functions 57
- TS16 Group 1 57
- TS16 Group 2 57
- Keypad Area Assignment 57
- User Code + Digit Functions 58
- Extended Monitor Times 58
- Vocabulary 59
- Keypad Function Terms 61
- User Code Options 65
- Disappearing Code Activations 65
- Assigning User Codes to Areas 65
- User Code Terms 66
- Automation Overview 67
- Automation Example 67
- Channel Activations 68
- Control Channel Options 1 69
- Control Channel Options 2 69
- Control Channel Options 3 69
- Control Channel Options 4 69
- Control Channel Locations 70
- System Triggers 71
- X-10 Options 71
- Output Control Assignments 72
- Chain Group Assignments 73
- Control Channel Terms 74
- ADEMCO LIMITED WARRANTY 84
Related products and manuals for Security access control systems AMX APEX Destiny 6100
(18 pages)© 2020, manymanuals.com. All rights reserved. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals