Amx Mio Modero FG148-04 User Manual download pdf (Page 2)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

5/11

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

REV: H

93-0148-04

6. Drop in your language pad and verify the alignment with the guide posts

on the PCB.

7. Place the top assembly back down on the PCB and return the unit over,

exposing the 6 screw points.

8. Tighten the 6 screw points.

9. Reinstall the battery, replace the battery door, and slide the door to lock it

in place.

Using the Programming Jack on the Mio R-4

The programming jack located on the back of the Mio R-4 (FIG. 2) is used for

communication between the device and TPDesign4. The programming jack

uses a CC-USB Programming cable, USB to mini USB (FG10-5965). You can

order the programming cable from AMX if you do not have one. While loading

your configuration file, make sure the device is situated in the charging cradle.

1. Remove the battery door (See Inserting the Lithium-Ion Battery Into the

Mio R-4).

2. Connect the mini USB programming cable (FG10-5965) into the

programming jack.

3. Connect the other end of the USB cable to the USB port on your

computer.

4. Configure the communication parameters in TPDesign4. For more infor-

mation, please refer to the Mio Modero R-4 Operation/Reference Guide,

available at www.amx.com.

Device Setup Pages - Setup Menu

The Setup Menu allows you to set and check the following device features:

• Project Information Functions

• Remote & Display Settings

• Date/Time Settings

• Sound Settings

• Protected Settings

• Battery Settings

To enter the Setup Menu, press and hold the Input and Back buttons for 6

seconds. Navigate the setup pages using the onscreen menu selections and

up and down arrows. For more information on the Setup Menu, please refer to

the Mio Modero R-4 Operation/Reference Guide, available at www.amx.com.

Protected Settings

The Protected Settings Menu allows you to set and check the following device

features:

• Options & Recovery

• Change Passwords

•Calibrate

• System Settings

• Reboot Panel

The Protected Settings Menu may be accessed through the Setup Menu.

Accessing Protected Settings menu items requires a password confirmation.

For more information on the Protected Settings Menu, please refer to the Mio

Modero R-4 User Manual, available at www.amx.com.

Note: To access the Protected Settings Menu for the first time, you must

provide the default password: 1988.

Changing Passwords

1. Select Protected Settings in the Setup Menu.

2. Select Change Passwords on the Protected Settings Menu.

3. Select one of the five passwords to be changed.

4. Enter, edit, and confirm changes to the password.

5. Select the Back button until you are out of the Setup Menu.

Calibrating the Mio R-4

1. Select Protected Settings in the Setup Menu.

2. Select the Calibrate button.

3. Touch each target as it appears on the screen.

4. If successfully calibrated, the Mio R-4 will return you to the Protected

Settings Menu.

Rebooting the Mio R-4

1. Select Protected Settings in the Setup Menu.

2. Select the Reboot Panel button.

3. Select Reboot.

System Settings

The System Settings page of the Protected Settings provides connection

status, gateway selection, and RF link information. Use the device’s up and

down arrows to move from viewable page to page.

Checking Connection Status

1. Select Protected Settings in the Setup Menu.

2. Select System Settings in the Protected Settings Menu. If the round

button at the top right of the first page is green, the system is connected.

3. Select the Back button until you are out of the Setup Menu.

Joining a Wireless Network

1. In the NXR-ZGW Browser-Based Configuration Pages, configure the

network’s gateway to allow joining. (For more information, please refer to

the NXR-ZGW/-ZRP-PRO Operator/Reference Manual, available from

www.amx.com.)

2. Select Protected Settings in the Setup Menu.

3. Select System Settings in the Protected Settings Menu.

4. Press the Network Scan button. The available networks are listed below.

Use the up and down arrows to navigate the menu.

5. Select the network by pushing it on the touch screen. A pop-up page

reading "Do you wish to connect to [Extended PAN ID number]" will

appear.

• To connect to the PAN, press the Yes button.

• To return to the Network Scan page without connecting to the PAN, press

the No button.

• If you do not make a selection within three seconds, the pop-up page will

automatically close in three seconds.

6. Select the Back button until you are out of the Setup Menu.

Note: Due to the wireless nature of the ZigBee network, temporary interference may

prevent a command from reaching the NetLinx master. If this happens while

increasing volume, the master may receive the command to increase the volume but

not the command to stop increasing it. Therefore, programmers should consider

setting safeguards for volume control, either established volume limits or timeouts

with the NetLinx master or more interactive adjustment from the Mio R-4 (i.e., direct

volume control), to prevent issues with lost commands.

Battery Low Indicator

When the battery charge level is too low to sustain continuous operation, a

popup window will appear on the touchscreen reading “Battery Low” and then

“Battery Very Low”. If the device is still not returned to the charging cradle, it will

then shut down.

Battery Settings

1. Select Battery Settings in the Setup Menu.

2. The battery level will be displayed on the Battery Settings Page. The

higher the number of green lights, the higher the charge.

3. Select the Back button until you are out of the Setup Menu.

Mio Remote Charging Base

The Mio remotes are complemented with the Mio-RCC charging base. To

charge the remote from the charging base:

1. Connect the terminal end of the power supply to the bottom external

power port on the Mio remote charging base.

2. Route the cable through the provided channel so that it comes out the

side of the base.

3. Connect the power cord to an external power source.

4. Place the bottom of the Mio R-4 into the charging base so the contacts on

the device are on top of the charging contacts inside the charging base.

The Power LED on the Mio R-4 blinks red to indicate it is charging and

illuminates solid red when it is done. A full charge cycle for a depleted

battery is approximately 3 hours.

Patents

This product is covered by the following patents:

AMX

U.S. Patent No. D 602,858

U.S. Patent No. D 520,495

U.S. Patent No. 7,786,623

This product employs or practices certain features and/or methods of one or

more of the following patents:

SIPCO, LLC

U.S. Patent No. 7,103,511

U.S. Patent No. 6,914,893

U.S. Patent No. 7,697,492

1 2

Comments to this Manuals

No comments

Amx Mio Modero FG148-04 User Manual Page 2

Comments to this Manuals