AMX NX-3200 User Manual download pdf (Page 2)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

6/14

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 •

www.amx.com

93-2106-03 REV: A

Note: Ensure the controller is fully booted when you press and hold the ID

pushbutton. Pressing and holding the ID pushbutton while the controller is

booting resets the unit to its factory defaults.

Changing the IP Address Once You Are Connected

Perform these steps to change the IP address once you are connected to

the controller:

1. Set the IP address on your PC to the same network the controller is

currently on.

2. In NetLinx Studio, select Diagnostics > Network Addresses from

the menu bar to open the Network Addresses dialog.

3. Click Get IP Information to enable the fields for editing.

4. Enter the System, Device (0 for NetLinx Masters), and Host Name

information.

5. To specify a network IP address, select Specify IP Address.

6. Enter the IP parameters into the available fields.

7. Click Set IP Information to retain the pre-reserved IP Address to the

Master.

8. Click Reboot Device to finish assigning the IP address to the Master,

and click OK to close the dialog.

Accessing the WebConsole

NetLinx Masters have a built-in WebConsole that allows you to make

various configuration settings via a web browser on any PC with access to

the Master.

The WebConsole consists of a series of web pages that are collectively

called the “Master Configuration Manager”. Refer to the NX Series NetLinx

Integrated Controllers WebConsole & Programming Guide for details on

the WebConsole.

From any PC with access to the LAN that the target Master resides on:

1. Open a web browser and type the IP Address of the target Master in

the Address Bar.

2. Press Enter to access WebConsole for the Master. The initial view is

the WebControl page.

FIG. 3 WebConsole (main page)

Default Settings

The following sections list the default settings for the controller.

Default User Names and Passwords

The following table lists the default user names and passwords for

accessing the NX-3200 through NetLinx Studio or the WebConsole.

Default IP Addresses

The following table lists the default IP addresses for the NX-3200.

Configuration

All items in this section require accessing the WebConsole.

Enabling Security

To enable security:

1. Select the Security tab on the WebConsole. The System Security

Details appear.

2. Click the Enabled check box to enable security and activate the

Access options.

3. Select the Access options which you want to require a login and

password.

4. Configure users and groups as necessary.

802.1x Security

The X-Series controllers support 802.1X, an IEEE Standard for Port-based

Network Access Control. To enable 802.1X, you must load an 802.1X

certificate file to your controller using NetLinx Studio. Once you add the

certificate file to your workspace, NetLinx Studio

transfers the file to the

appropriate directory on the controller.

1. Click to select (highlight) a System (in the Workspace tab of the

Workspace Bar).

2. Right-click on the Other folder to access the Other File Folder context

menu, and select Add Existing Other File.

3. In the Add Existing Other File dialog, locate and select the certificate

file (.crt) that you want to add to the selected System. Change the

Files of Type option to All Files (*.*) to look for other file types, if

necessary.

4. Click Open to access the File Properties dialog, where you can view/

edit general file information for the selected file.

5. Click OK to add the file to the selected System. The file should now

appear in the Other folder under the selected System.

Setting the Clock Manager Mode

To set the clock manager mode:

1. On the Manage System tab, select a Time Sync option.

• Network Time: When this option is selected, the Master will connect to

the default NIST Server to get date and time information. You can

select a different NIST Server (or specify the IP Address of a known

NIST Server) on the NIST Servers tab.

• Stand Alone: This option lets the Master use its own internal clock.

When this option is selected, the Date and Time fields are available on

this tab.

2. Click Accept to save these settings to the Master.

Hardware Information

This section lists important hardware information for the NX-3200.

Port Numbers

Mounting the NX-3200

The NX-3200 ships with removable rack ears for installation into an

equipment rack. Use the supplied #8-32 screws to secure the rack ears to

the sides of the controller. You can attach the rack ears toward the front or

rear panel for either a front-facing or rear-facing installation.

Use the four #10-32 screws supplied in the mounting kit to secure the

controller to the rack.

Default User Names and Passwords

User Name Password

NetLinx Studio netlinx password

WebConsole administrator password

Default IP Addresses

IP Address Subnet

Static IP 192.168.1.3 255.255.255.0

ICSLAN 198.18.0.1 255.255.0.0

Link-local 169.254.x.y, where x and y are the least significant two

octets of the MAC address.

NX-3200 Port Numbers

RS-232 RS-422/485 IR/Serial I/O Relay

2-4, 6-8 1, 5 11-18 22 21

1 2

Comments to this Manuals

No comments

AMX NX-3200 User Manual Page 2

Comments to this Manuals

Related products and manuals for Recording Equipment AMX NX-3200