AMX NXD-435 Installation Guide download pdf

Installation Guide

NXD-435 4.3" Modero

Wall/Flush Mount Touch Panel

For more detailed installation, configuration, programming, file transfer, and operating

instructions, refer to the NXD-430/435 Operation/Reference Guide, available online at

www.amx.com.

Overview

The NXD-435 Modero

Wall/Flush Mount Touch Panel includes a mini-USB port for

programming, and five NetLinx-programmable buttons. All power is supplied via

Power Over Ethernet (PoE), utilizing a PS-POE-AF PoE Injector (FG423-80) or

equivalent PoE device.The NXD-435 comes in black (FG2262-03) and white

(FG2262-04).

Specifications

Panel Connectors and Wiring

FIG. 2 shows the connectors located on the NXD-435 Modero panel. The mini-USB

port is used for programming the touch panel.

For more information on connection and use of the Panel Connectors, as well as

information on programming, please refer to the NXD-430/435 Operation/Reference

Guide, available at www.amx.com.

Capacitive Touch Buttons

The NXD-435 has one main button on the front of the device, in the center of the

bezel, and two smaller buttons on each side. This button has several uses:

• Press the button once to start a previously programmed function, or to turn off

the display if not previously programmed.

• Press and hold the button for 6 seconds to put the device into Setup Mode.

• Press and hold the button for 9 seconds to enter Calibration Mode.

• Press and hold the button for 20 seconds to reboot the panel.

The NXD-435 also has four smaller buttons, two on either side of the front button, that

may be programmed for individual functions.

All five buttons on the NXD-435 utilize capacitive touch, which detects the electrical

conductivity of human skin and reacts directly to touch. This allows the button to resist

wear and dirt, as the button does not have any actual physical button to depress.

FIG. 1

NXD-435 4.3" Modero Wall/Flush Mount Touch Panel - Black

NXD-435 (FG2262-03/04) Specifications

Dimensions (HWD): • NXD-435: 4.13" x 5.5” x 2.13" (10.48 cm x 13.97 cm x 5.40 cm)

• CB-TP5 Rough-In/Wallbox (optional): 4.27" x 5.14" x 3.40" 

(10.86 cm x 13.06 cm x 8.64 cm)

Weight: • 0.65 lbs (0.29 kg)

Power 

Requirements:

• PoE Powered - No local Power Supply needed

• Max power draw: 5.5W.

Memory (Factory

default):

• 128 MB SDRAM

• 256 MB integrated Flash Memory (not upgradeable - factory

programmed)

Certifications: • FCC Part 15 Class B

•CE

• IEC 60950

•RoHS

Panel LCD 

Parameters:

• Aspect ratio: 16 x 9

• Minimum brightness (luminance): 280 cd/m2

• Channel transparency: 8-bit Alpha blending

• Contrast ratio: 250:1

• Display colors: 256 thousand colors (18-bit color depth)

• Dot/pixel pitch: 0.14 mm

• Panel type: WQVGA

• Screen resolution: 480 x 272 pixels (HV) @ 60 Hz frame

frequency

• Viewing dimensions: 2 3/16" x 3 13/16" (5.56 cm x 9.68 cm)

Active Screen Area: • 2 1/8" x 3 3/4” (5.40 cm x 9.53 cm)

Viewing Angles: • Left/Right/Up/Down: 80/80/60/80

Front Panel 

Components:

• Center Button: Capacitive touch button provides both access to

the Setup and Calibration pages and toggles the panel between

a "sleep" or "wake" state. This button is also user-

programmable.

• Capacitive Touch Buttons: four user-programmable buttons, two

on either side of the Center Button.

Center Button

Touch screen

Capacitive Touch Buttons

NXD-435 Specifications (Cont.)

Side Panel 

Connectors:

• Ethernet 10/100 Port: RJ-45 port for 10/100 Mbps

communication. The Ethernet port automatically negotiates the

connection speed (10 Mbps or 100 Mbps), and whether to use

half duplex or full duplex mode. Power is supplied through

Power Over Internet (PoE). NXD-435 panels communicate with

the NetLinx Master using the ICSP protocol over Ethernet. LEDs

show communication activity, connections, speeds, and mode

information:

L/A-link/activity - Yellow LED lights On when the Ethernet cables

are connected and terminated correctly and then blinks when

receiving Ethernet data packets.

SPD-speed - Green LED lights On when the connection speed is

100 Mbps and turns Off when the speed is 10 Mbps.

• Mini-USB Connector: 5-pin Mini-USB connector used for

programming, firmware update, and touch panel file transfer

between the PC and the target panel.

Operating /Storage

Environments:

• Operating Temperature: 0° C (32° F) to 40° C (104° F)

• Operating Humidity: 5% - 85% relative humidity

(non-condensing)

• Storage Temperature: -20° C (-4° F) to 60° C (140° F)

• Storage Humidity: 5% - 85% RH

Included 

Accessories:

• NXD-435 Installation Guide (93-2262-03)

Other AMX 

Equipment:

• CB-TP5i Rough-In/Wallbox (FG038-11)

• Back Cover for the CB-TP5i Rough-In/Wallbox (FG038-12)

• PS-POE-AF PoE Injector (FG423-80)

• NXA-BEZP-435-BL Black Portrait Bezel Kit for the NXD-435

(FG2262-12)

• NXA-BEZP-435-WH White Portrait Bezel Kit for the NXD-435

(FG2262-13)

• CC-USB Type-A to Mini-B 5-wire programming cable 

(FG10-5965)

• NXA-RK5 Rack Mount Kit for 5" Wall Mount panels (FG2904-55):

- 5" Rackmount 

- Four Screws, #10-32 x.625, PH Truss, BLK 

- Four Washers, #10, Black Nylon

- Three Screws, #4-40 x.250, PPH, BLK

FIG. 2 Connector layout on the NXD-435 Modero Wall/Flush Touch Panel

Ethernet 10/100 port

Mini-USB port

Back box

1 2

Summary of Contents

Page 1 - NXD-435 4.3" Modero

Installation GuideNXD-435 4.3" Modero® Wall/Flush Mount Touch PanelFor more detailed installation, configuration, programming, file transfer, and

Page 2 - Installation of the NXD-435

Comments to this Manuals

No comments

AMX NXD-435 Installation Guide

Browse online or download Installation Guide for Touch screen monitors AMX NXD-435. AMX NXD-435 [et] User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Touch screen monitors AMX NXD-435