AMX MXT-1900L-PAN User Manual download pdf (Page 2)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

3/14

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-5968-41 REV: A

Wiring a Power Connection

To use the 2-pin 3.5 mm captive wire connector with a 12 VDC-compliant power

supply, the incoming PWR and GND wires from the external source must be

connected to their corresponding locations on the connector (FIG. 4). The connector

uses locking screws to insure a connection to the device, so make sure to insert and

tighten the screws before applying power.

1. Insert the PWR and GND wires on the terminal end of the 2-pin 3.5 mm

captive wire cable. Match the wiring locations of the +/- on both the power

supply and the terminal connector.

2. Tighten the clamp to secure the two wires. Do not tighten the screws

excessively; doing so may strip the threads and damage the connector.

3. Verify the connection of the 2-pin 3.5 mm captive wire to the external

12 VDC-compliant power supply and apply power.

Configuring the MXT-1901-PAN

The MXT-1901-PAN is equipped with a Settings app that allow you to set and

configure various features on the panel. For more information on connecting and

configuring the MXT-1901-PAN to a network, please refer to the Modero X Series G5

Programming Guide, available at www.amx.com.

Accessing the Settings App

To access the Settings app on the MXT-1901, press and hold the Sleep Button

(FIG. 1) on the top of the panel for 3 seconds. The user will be prompted to release the

button to enter the Settings app.

Accessing the NetLinx Subpage

1. From the Settings app page, select NetLinx. This opens a password keypad.

2. Enter the panel password into the keypad (the default is 1988) and select OK to

access the subpage.

Setting the Panel’s Device Number and Device Name

In the NetLinx subpage:

1. Press Device Number to open the NetLinx editing window.

2. Enter a unique Device Number assignment for the panel and press OK.

3. Enter a unique Device Name assignment for the panel and press OK.

Accessing the Ethernet Subpage

1. From the Settings app, select Ethernet. This opens a password keypad.

2. Enter the panel password into the keypad (the default is 1988) and select OK to

access the page.

Connecting to a Master

The panel requires that you establish the type of connection you want to make

between it and your Master.

In the NetLinx page:

1. Press Mode to toggle through the available connection modes:

2. If you have enabled password security on your Master, you need to set the user-

name and password within the device.

a. Select Username to open the NetLinx editing window.

b. Set your Username and Master Password.

e. Click OK to return to the NetLinx page.

Configuring the Panel to a Network

The first step is to configure the panel’s communication parameters. This only

configures the panel to communicate with a network, and it is still necessary to tell the

panel with which Master it should be communicating.

Network Communication With a DHCP Address

In the Ethernet subpage:

1. Toggle the DHCP/Static field to open the DHCP/Static window. DHCP is the default

setting.This action causes all fields on the Ethernet subpage (other than Host Name)

to be greyed-out.

2. Select Host Name to open the Host Name window. Enter the new host name

and click OK.

Network Communication with a Static Address

In the Ethernet subpage:

1. Toggle the DHCP/Static field to open the DHCP/Static window.

2. Select Static in the window. This opens the Static IP editing window.

3. Click on any field to open either a keypad (for numeric entries) or keyboard (for alpha-

numeric entries). To minimize the keypad/keyboard, click the two downward-pointing

arrows at the bottom right corner of the screen.

4. Enter your network’s information in the Static IP editing window. To move from field to

field, simply press the next field you wish to edit.

5. When finished, click OK to save your changes and return to the Ethernet subpage.

FIG. 4 NetLinx power connector wiring diagram

PWR +

GND -

To the Touch Panel

Power Supply

Connection Modes

Mode Description Procedures

Auto The device connects to the first

master that responds.

This setting requires that you set

the System Number.

Setting the System Number:

1. Select Master System Number to open

the keypad.

2. Set your Master System Number and

select OK.

URL The device connects to the

specific IP of a master via a TCP

connection.

This setting requires that you set

the Master’s IP.

Setting the Master IP:

1. Select the Master IP number to open the

keyboard.

2. Set your Master IP and select OK.

Listen The device “listens” for the

Master to initiate contact.

This setting requires you provide

the master with the device’s IP.

Confirm device IP is on the Master URL list.

You can set the Host Name on the device

and use it to locate the device on the master.

Host Name is particularly useful in the DHCP

scenario where the IP address can change.

1 2

Comments to this Manuals

No comments

AMX MXT-1900L-PAN User Manual Page 2

Comments to this Manuals

Related products and manuals for Touch screen monitors AMX MXT-1900L-PAN