Amx Zero Cross Module RDM-ZC50 User Manual download pdf

Installation Sheet

RDM-ZC50 Zero Cross Module

6000 W

The RDM-ZC50 Zero Cross Module is a 6000 W solid-state zero-cross

relay built for extra large loads. It is designed for use with the RDA series of

enclosures, in an AMX Lighting™ modular digital dimming system. The

RDM-ZC50 module's 120 VAC and 277 VAC ratings are CE, UL, and C-UL

approved.

RDM-ZC50 UL and C-UL Ratings

120-277 VAC, 6000 W

Suggested Switched Loads

• Incandescent

• Electronic transformers

• HID ballast

• Fluorescent ballast

Specifications

• Dimensions (HW): 10.00" x 2.75" (25.40 cm x 6.99 cm)

• Non-phase dependant

• Use 75°C (167°F) copper conductors only

• Torque terminals to 16 in-lbs. (7.25 kg-m)

• Max. wire size: 6 AWG; 14 AWG min.

• Wire stripping length: 0.35" (9 mm)

• Weight: 1.0 lb. (0.45 kg)

• BTU/hr: 400

• Control current: 45 mA @ 12 VDC

Caution: Pre-Installation Notes

• All Class 1 wiring must be connected to proper terminals.

• All control wiring must be connected to proper terminals.

• Disconnect power while installing or connecting the unit.

• Keep top and bottom air vents clear at all times.

• Test loads for shorts before connecting.

• Run all low-voltage and control wires away from heat producing parts

of the dimmer.

• Each dimming circuit must have a separate neutral connection.

• All electrical ratings are for continuous duty.

• AC lighting loads only.

• For indoor use only.

• This module may require extra power from the AXlink connection or an

external power supply connected to the control card.

Connecting the RDM-ZC50 to the AMX Lighting Master

Lighting Application Drawing

FIG. 1 RDM-ZC50

Low-voltage control

wiring: 4-pin controller

to AMX Lighting master

controller

Zero cross relay

Line in (hot)

Load out

High-voltage

connections

Mounting points

FIG. 2 RDM-ZC50 connections

FIG. 3 RDM-ZC50 wiring configuration

Pin 4 (GND)

Pin 3 (RLY)

Pin 2 (DIM)

Pin 1 (+12 V)

3 (-)

1 (+)

RDM-ZC50 4-pin module connector

4-pin plug from RDM series module

NOTE: The 4-pin plugs from the module connector to

the 4-pin connector on the master (black plug cover facing up).

Ballast

Circuit breaker

panel

Neon lights

(cold-cathode, on/off)

Neutral

Load

All neutrals are common

to the Neutral block in the

enclosure. Provide a

separate neutral for

each load.

Load

Neutral

Fluorescent Lighting

Line in (HOT)

Load

Neutral

1 2

Installation Sheet 1

Summary of Contents

Page 1 - Installation Sheet

Installation SheetRDM-ZC50 Zero Cross Module6000 WThe RDM-ZC50 Zero Cross Module is a 6000 W solid-state zero-cross relay built for extra large loads.

Page 2

AMX Corporation reserves the right to alter specifications without notice at any time. For full warranty information, refer to the AMX Instruction Man

Comments to this Manuals

No comments

Amx Zero Cross Module RDM-ZC50 User Manual

Browse online or download User Manual for Hardware Amx Zero Cross Module RDM-ZC50. AMX Zero Cross Module RDM-ZC50 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Amx Zero Cross Module RDM-ZC50